v-plex

Just got this new clutch for the MTD. Is the piece of what looks like a copper wire just for shipping and should it be taken out before install? Thanks I have no clue about these.

Looking for a v-plex clutch for 3/4 shaft. Thanks

Picked up this very nice condition V-Plex TC driver with 1'' bore the other day. Fits great, looks great but isnt there supposed to be a spring up inside where the arrow indicates? I get no resistance when I press in that half of the pulley. So if it needs one, how do I open it up...

I have the clutch. Need the driven. Wont you help this poor old ugly bastard? Bless you. JT

Would love to learn more about the deal with this bike. I know its mtd. But what kind and year. Also its slow, not sure if the torque converts not working right, but it goes like 8 mph with high rpms. Thanks for any help!!

Never used, bought it a couple years ago but never found a use for it. Complete kit, half the box, no instructions. Requires jack shaft. $112 shipped to lower 48, PayPal fees apply.

NOS V-Plex 2 speed clutch I have been saving for a project for years. Operates with a cable much like the early Heathkit bikes. I have only seen one other 2-Speed V-Plex unit which belongs to OldMiniBikes member Richtrix who reports it works great on his Tecumseh Powered Doodlebug...

I have a nos v-plex 2 speed clutch and was thinking about using it on my minibike project. Has anyone here ever tried one of these setups? Thanks in advance, Richie

This stuff is leftover from my days as "King of the MTD Wheelie" ..:cool: There are a pair of NOS V-Plex 6" Drivens.... 5/8" bore. They have different springs and different engagement speeds so you can fool around with the one you want. Complete with NOS shaft (9") that has machined...

****SOLD*****:hammer: After searching forvever I bought a whole 'nother bike to get this original V-Plex TAV assembly for my MTD, and boy was it worth it. Turned it into a whole different bike. Lots of top end speed and enough bottom end torque to pull the front wheel off the ground and...

NOS V-Plex 6" Driven Pulley and Belt. This is the style that was used on the larger MTD bikes like the Trail Flite...5/8" bore with built-in keys fits on jackshaft...includes a NOS genuine V-Plex belt which is approx 29" o.d....I believe this is the correct belt for MTD also but I'm not sure...

One V-plex driven, locked up or I do not understand how it works. But everything else on the clutch and bike came apart with PB blaster including the set screws. The secondary spring is removable but I'm not messing with the primary one which will move and looks good. I would say there is an...

phot courtesy of Pomfish V-Plex unit (symetrical) and jackshaft.......Uses 21/32" (5/8) wide belt. .

Looking for whatever would be considered the "correct" V-Plex driver for my MTD.... I already have a V-Plex driven unit (symetrical) and jackshaft....... PM me if you've got something or maybe post up a picture that will help.... >>>Like to find an original seat too but I don't...

Here's a NOS V-Plex 6" Driven 5/8" bore complete with shaft (9") and 2 belts. Not sure what was OE on-Maybe Snowco?? Belts are also 5/8" $60 + $10 shipping or make reasonable offer.

looking for working v-plex driven converter

about year and half ago i bought my first bike, it was just a frame an mtd columbia it did not have the jack shaft, so i bought one on ebay that came with the driven part of the converter , i stuck a 6.5 honda motor on and found a used comet 20 driver and matched a belt and she took off great i...

jackshaft, mounting plate and v-plex clutch (complete). Good working condition.