width

Hi, I recently got a shock from motovox , however they no longer give you the needed accessories :sad: ray traverio has told me the spacers are available but not the axle. Go Karts, Kids Go Carts, Scooters, Beginner Youth ATVS, ATV Trailers, Quads | Family Go Karts has axles and i think...

I have a cat99 6" Driven and its 2.160 ... The cat99 is shot and I'm looking into what it will take to get a 30 series on there. Thanks Kevin

My 12" wheels still have tires on them so i can't exactly tell how wide the rims are? They look to be around 2-1/2" wide. I also wondered if people are running any other sizes than the 3.00-12 tires on a Rupp Roadster 2? There are some scooter tires out there in metric sizes, is anyone...

Say the tire is 21x12x8 .... or ... 21x9x8 what WIDTH wheel is required to maintain the tire diameter? 21" in both examples. I ask because my tire currently is 21x12x8 with a 9" WIDE wheel and both front and rear tires are 22-3/4" tall. Too tall for the bike. Tires were measures with 1/2...

A quick check shows mine at about 9" ...

Can anyone recommend a cover for the DB30R? I measured the length at 48", width at 24", and height at 36".

I have a Trisport that came with a Horstman torque converter. I am unsure of the model the trike is, but I know it is a TS series thanks to this site. Does anybody know what the specs are for belt and center distance? I guess most important is belt width as I can figure out center distance...

Hey so since I had to saw my Black Beauty axle up to ge the brake off I'll need to order a new one. Hopefully OldMiniBikes has these? I don't have the axle pieces anymore so I'll need help on it's size. I might have two small peices so measure for width but not sure of the length. May have been 9...

Does anyone know the width of a CRF50 rim hub w/drum brake :shrug: I want to use a set on one of my builds but don't want to buy them if they are too wide :doah:

Could anyone please tell me what the width of the plastic Baja Warrior fender, that is available at OldMiniBikes, is? Front and/or rear. For S&G's, how about the older steel rear fender? My current tire/wheel is 7" wide, so I'm trying to find a round top fender that will cover this wheel. TIA! Daniel

Working on a MB1210 for the build off. Would anyone happen to know the spacers needed for the rear axle? The swing arm measures 5 3/4" inside the rear mounts. However, the front measure 6" inside the pivot point so I think it may be bent slightly. I'm also looking for axle adjusters/chain...

Can someone help me out with some dimensions. I need the width of the upper frame on the Luther trail gote. Please and thank you.

Im looking for 3 bearings of the size in thread title. I have been searching for a couple days and have not been able to find much. I know they are out there because I have found some but not quite what Im looking for. If someone can help me thanks. Im trying to redoing my mini trike "Ding...

Hey guys, Relative noob here with a homemade frankenbike. Planning on going to a bigger sprocket on my rear axle to gain more acceleration. I'm getting a tad bit concerned about clearance as my current tire is a 13-5.00-6. I have a 4" wide rim at the moment and would prefer to use it when...

Is it just me or has anybody else noted that the tread WIDTH (where "the rubber meets the road") on minibike tires is less than it used to be back in the day? We are looking for 5.30 X 4.50 X 6 studded/knobby tires for the Ruppster's Bonanza build. I'm finding lots of tires available (some at a...

I just got a new Carlisle knobby tire that is supposed to be 4.10X3.50-4 but the tire width is over a half inch narrower than the old tires I have that are the labeled as the same size. The difference was notable right out of the box and there is no way I am going to ride on these. I...

Hello everyone, I forgot to ask what width belt the Montgomery Ward T555 requires for its tourque converter. Thanks,Joe

I have spent 5-6 hours on the Net and a couple hours driving around to lawn mower shops/power equipment dealers with no luck finding what I want. I picked up a Cheng Shin 4.80/4.00-8 for the front tire on my 670 Tote Gote. On the rear I want the same general tread pattern but want the tread...

Just wondering if anyone could measure the actual tire width on a stock doodlebug? I know the numbers say 5.8 inches but I'm looking for an actual measured number.

What is the usual foot peg width on a mini? Im building my bike with a 5hp briggs and a tav. the entire width of the engine is 14" so in order to be comfortable iv got to move my pegs out to like 22" that means adding 3" extentions off the frame. Does this sound reasonable? It just seems like...