If I delete and cap off the primer bulb nipple on the carb body, will I have to enlarge the tiny vent hole that's drilled in the side of the carbs main body?
What symptoms would this cause if I were to leave the tiny vent hole unaltered if the primer line nipple was capped off?
I...
Hello Guys.. Anybody fight the briggs 3-5 HP Updraft Fuel Bowl flooding? Horizontal Tote Gote 5 HP Engine, The Float was tested Hours under Gas to check for leak and passed ,,, We think it Is leaking at our needle valve fitting gasket.Anybody else have this problem?
The spring drain thingy broke on mine, plus it is dented. If you have a special place that is good to order from, I'd like to hear about it. Will take used parts too. Thanks.
Here is the carb.
I was running .028 size jet and noticed i had bad throttle reaponse. So I ins5alled a .032 jet....runs perfect but now carb leaks. It seems like its coming from the top of the bowl. I made sure I put rubber seal back in... I need help.
Upgrades: dyno cam. 18lbs springs. Header. Air filter(no...
The crank case was full of gas and oil. The gas had migrated from the tank to the crank.
Changed the oil & filter.
Removed the carb, pulled the float bowl, gently cleaned the jets with WD 40, air and a small wire. The bowl was clean when 1st disassembled.
1-1/2 gallons of fresh gas was put...
nice units, I can't get the pictures to load. toss me a pee em with your email and I will send.
$40 shipped to U.s. 48 states. Carb is float bowl type and may need a cleaning or rebuild.
Tank is black plastic with center fill.
I was looking on ebay for a jet holder for my vm22 since I misplaced the one for mine and I came across this.... hopefully it fits the bowl on my carb and works well.. This would make tuning the carb easier that having to keep trying different main jets..... Vintage Motocross MX Precision...
I can't seem to find what's causing the carb to leak. It will slowly drip fuel from the float bowl until the entire tank is drained onto the ground. Thus far, I've tried changing the fuel shutoff valve gasket, the float bowl gasket, and the three carb gaskets with no success.
Guys,
Anyone know where I can get a replacement carb bowl gasket for the Harbor Freight Predator 212 engine? I am having a hard time finding it online.
Thanks.
Gang,
Can someone tell me the correct bowl needle and rubber needle seat kit pn# number for an H35? The engine model is H35-45158E if that helps any. The engine is on my '67 Rupp Electra.
I think the kit pn# is 631021, but I'm not for certain.
Thanks in advance for any help!!:thumbsup:
I picked up a Sears labeled Tec the other day in a bike/parts buy. its a side popper 3 or 3.5 have not checked the numbers yet. its got one of those primer bulb bowl carbs on it, of course the bulb is rotted and gone.
Normally I have no use for something like this but since period correct...
I have a 5 hp power sport engine that was running only if I kept pushing the primer blub. I removed the carb and cleaned out the holes in the bowl bolt that were pluged up. I removed the float and needle and sprayed carb cleaner through all the holes in the carb. I also cleaned out the gas tank...
Searching for a float bowl and choke assembly. As well as the 7.5 gr float in my other thread. Willing to trade for an H50 allum lighted flywheel and stator or pay in cash.
Thanks, Joe 51
I need a carb fuel bowl nut number 167... snowblower,i think the last year tecumseh was in business,carb has no numbers for IDing but at least the bowl nut is numbered 167... Thanks
I am working on a Briggs 143302 and a 142302. I want to keep them as original/vintage as possible. I need the fuel filter/glass sediment bowl part #99910 for both. I can't find any, but on Ebay I find lots with a different part (690612, 393169) number that LOOK identical in the pictures...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.