cable

  1. 20190525_100728.jpg

    20190525_100728.jpg

    Cable work.
  2. T

    throttle cable 1969 taco 3 hp briggs & stratton

    hello all, i need a throttle cable , 1969 taco 44 orig throttle cable is no good , it has a small round ball on the end were it goes into throttle were can i get one that will fit ?? thanks bobby
  3. R

    Brake Cable Replacement( General Appliance MW Bike)

    Hello All, Can anyone tell when I can get a good quality replacement cable for the brakes on my 1971 Montomery Wards bike l want to either reuse the existing cable or get a good quality replacement. No sure if I will be able to get the molded end section on the new cable. Thanks for the time...
  4. D

    Most correct brake cable

    Front bracket appears to be 5/16". Rear threaded on brake arm appears to be #12x24. 56" cable. Clark cyclone. Is there a close match to original brake cable available?
  5. mini one

    7/8" throttle and cable?

    New , used, whatcha got? I'll be at the EC race tomorrow in NY too
  6. Taco Loco Joe

    Cable Clamps

    Anyone out there have a good technique for putting on those cable clamps without scratching the paint? I was wrapping some clear tape on the frame first . Joe
  7. Sixpac440

    Want a Heald Speedometer and cable

    Looking for a Heald Speedo and cable as the title says!! Kevin
  8. Harleys Papa

    Cable Stay

    I need a cable stay like this one, if you have one PM me and I would be more than happy to buy it :thumbsup:
  9. Aston jag

    Another cable end method (?)

    I came across this method for fastening cable ends: Bowden Control Cables (making, repairing, or modifying control cables) - Looks really good to me, and brass is nice to turn on a lathe when you need to make the ends themselves. Sorry if it has already been discussed here.
  10. R

    Can I Cut a Brake Cable to Length?

    I'm going to replace my brake lever and cable assembly. I need a cable housing about 50" long. All I'm finding are longer, with each end having metal cap. Can I cut off the end down at the wheel to the length I need ? It looks like it goes into a socket and would be immobilized and covered.
  11. tbird

    DB30s rear brake cable barrel

    I have a DB30s (Metal fenders) that I just picked up and the brake caliper and brake cable were messed up. I got a cable and caliper off a person on here and the barrel end that goes in the brake lever is smaller then the original barrel. He said he took it off of a DB30s just like the one I...
  12. danford1

    Brake cable adjusting sleeve for drum brakes

    I'm looking for a brake cable adjusting sleeve for drum brakes like the picture below. I know I can buy them at various places but where can I get one without paying a lot for shipping? a lot of places want $7 to ship a tiny thing like this. Heck it probably only sells for $3... Any...
  13. FOMOGO

    My brake cable is afraid....

    Any body have a solution for a frayed cable end????? The rear brake on my Bronc is frayed and I can finagle it though the first pin with its smooth hole. BUT I cant get it to go though completely on the rear pin as it has a cross screw to tighten down to retain it. So it hangs up on the edge of...
  14. OPEtech

    WTB Heald SST-16 throttle cable

    Would anybody know where would be a good place to purchase a throttle cable at least 106" long, for my daughter's Heald Super tryke? Ron Kimball from Power Tec does not carry them anymore. Even a good quality kit to custom-make one would help. Any ideas would be appreciated.
  15. tacobender

    taco brake cable clevis for 44

    looking for the attaching cable clevis for an taco 44 attaches cable to brake arm( 2 pieces) will take 2 if anyone has any- restoring to late model 44's
  16. S

    Cutting throttle cable

    Looks like I'm going to have to shorten a throttle cable I'm getting from OldMiniBikes. Anybody have any insight on what problems might encountered? I've never had to cut one of these, so I'm wondering about how to handle replacing that crimped metal "button" on the carburetor end. Any help would be...
  17. S

    Throttle cable adjuster advice needed

    Hello: Looking for advice on where to get a throttle cable adjuster (with the jam nut) to fit the OldMiniBikes R261 cable that I want to order. Going to be using it with my NOS Odeon twist grip. Don't really see the adjuster I want on the Warehouse site. I'm a little unsure of the size as I don't...
  18. Biffmini

    Front brake cable

    I have a few. $4.00 each plus shipping.
  19. Not so mini bike

    Harley throttle cable or cable adjuster

    I bought some 1" Harley throttles and tried to used a 1" mini bike throttle Housing my and it didn't quite work. I bought just the Harley housing for a dual cable and the throttle feril different. I need a 5/16-18 for it. Anyone experience this same issue or know where I can get one.
  20. BWL

    Cable Stop Hack

    https://www.youtube.com/watch?v=wPjDaaiCrgA
Top