driven

  1. S

    What is this mini bike with go power wheels & a 2 speed belt driven drivetrain

    Curious to find out what this is. The engine clutch is a dual pulley. the kick lever engages one of the two belts. The brake is an interesting set up as it has a belt wrapped around a pulley. any help would be appreciated
  2. gumpit

    40 series driven parts

    Is there a stronger reverse spring than the yellow reverse spring for the 40 series driven?
  3. bigevilone2

    Powell Salsbury driver and driven

    Powell clutch for sale. Needs to be cleaned up. All parts are there. NO BELT ! $115.00 Shipped PAYPAL ONLY ! Thanks for looking !
  4. gbabins1

    TAV question

    I picked up a new TAV about a year from OldMiniBikes warehouse. They were pretty cheap so I grabbed one and it sat for about 1 year before I got around to using it. I put it on a few weeks ago and noticed right away the the driven unit has a slight wobble in it. At first I suspected the 3/4 jackshaft...
  5. G

    NOS Comet series 40 clutch, belt, driven

    I have a new never used Comet series 40 torque converter with belt and driven pulley The 2speed jackshaft is not included in this sale but is offered n another post. More photos here: grifftek.com/craigslist/comet_series_40_torqu_converter_wpcl/ Prrice is $175.00 shipping from 90242...
  6. Sprocket86

    Tav driven RED spring.

    Ordered a China knock off 30 series driven pulley from BMI karts as well as a Comet Yellow driven spring. I ordered the yellow spring under the assumption that the knock off driven would have the plain natural colored spring that seems to be even weaker then the Comet green spring. Upon...
  7. O

    TAV 30 on predator 212 6" driven clutch right size?

    Looking to buy a tav 30 on ebay. There are two kits one with a 6" clutch and another with a 6" 5/8" inner diameter Driven Clutch. Not sure if either one matters. Which one should I get for my predator 212? thanks
  8. Old_iron

    Floating comet driven?

    I am mounting a 30 series driven on a keyed jack shaft. Does it have to be held in horizontal position with a pair of collars or can it float?
  9. gammatg

    Brand new Comet 20 series driver and driven and TAV2-30

    Brand new never used in their original box TAV2-30 $150 20 series 75 bore Driver $60 Series A 5/8 bore Driven $70 Buyer pays shipping. Thanks OldMiniBikes!
  10. myjunk

    Drive / driven pulley question

    I'm not sure I'm in the right section, but I will ask the question anyway, please move it to the right section if need be. I am building a go kart out of left over pieces I have lying around. I am having a senior moment and want to be sure I have the pulleys going in the right direction before I...
  11. MINI-MATIC

    F.S RARE Lil Indian Minimatic 2 speed tranS Driven Clutch NOS Mint Fairbanks Morse

    For Sale,I am selling,my last NOS,Mint Fairbanks Morse Two Speed Transmission Clutch.I re zinc plated it fresh,as the original plating was a bit scaly,absolutely NO rust though,never been mounted on a bike.This is a rare find item to help complete the Mini matic 2 speed setup...Asking $150.00...
  12. Sixpac440

    What is the Comet 30 6" Driven width?

    I have a cat99 6" Driven and its 2.160 ... The cat99 is shot and I'm looking into what it will take to get a 30 series on there. Thanks Kevin
  13. H

    TAV Driven Pulley Locknut Question?

    Well I have a new generic TAV. It came with the driven pulley locknut (nylock) loose. Is this an adjustment or should I simply torque it to a certain spec. Or just go ahead and tighten it? Sorry for the newbie question but I did search and came up short. Three letter words like "nut" and "TAV"...
  14. MINI-MATIC

    Lil Indian 2 SPEED Trans Original Driven Clutch model 600,6000

    Up for sale is a Rare used Lil Indian Original 13 Tooth Driven Clutch that go's on the jack shaft Teeth are in excellent not worn condition.This is a Fairbanks Morse Clutch and is next to impossible to find! Missing the 2 springs that hold the shoes in place.They were misplaced and at this point...
  15. OND

    Powell Driven Bearing Replacement

    Just as the title says, I'm replacing the bearings on my Powell driven. Also I'll add some 1/8'' spacers between the pulley halves so I can use a 3/4'' top width 20 series TAV belt. This is the driven torn apart. This is the main shaft with the old bearings still on it...bearings are a...
  16. OND

    "WTB" Powell Driven

    Anybody got a Powell driven for sale ? Going on a D series Powell . Thanks in advance ond
  17. JohnnyTillotson

    Fairbanks Morse Driven

    Want a Fairbanks Morse Driven pulley for jackshaft on MTD Trail Bike
  18. smudvapor

    71 Rupp Driven Unit

    Is there any special way one of these goes together? I can't find anything on the web. When we pulled the TC and the driven off the bike it all worked. Now I can't get it to work. I have checked the TC a bunch of times so I am thinking we did something wrong with the driven unit.
  19. 2SlickNick

    Trade - 7" Driven

    Hey Everyone, I have (no ID stamps ) 20 series, out-board, 7" driven unit for trade. I also have a 1" bored/keyed hub on a 4" bolt pattern that uses 5/16" bolts - that I could throw in depending on what you have. I would trade the driven unit for DB30 rear rim and axle OR a 5/8" rear...
  20. JohnnyTillotson

    Need V-Plex driven

    I have the clutch. Need the driven. Wont you help this poor old ugly bastard? Bless you. JT
Top