gx140

  1. 20190624_210759.jpg

    20190624_210759.jpg

    Honda GX 140 engine installed after I took the GX160 off for another minibike.
  2. DeadPixel

    CL1 cam and GX140 valve springs?

    I have the high torque version of the CL1 cam and noticed the cam card recommends only 10.5 LB valve springs. Its the hardened version. That seams pretty light. I am rethinking my build and kinda thinking of trying the GX140 springs as NR says there 16# will these run to the 6K that I am going...
  3. astrowrench

    Genuine Honda GX140 Emulsion Tubes

    Genuine Honda 140 E-Tubes $6.00 Shipped anywhere In the US Free PM Or E- Mail Me astrowrench@gmail.com
  4. astrowrench

    Genuine Honda GX140 Emulsion Tubes

    Genuine Honda 16166-ZE1-00* These are the real GX140 Honda E-Tubes$6.00 Shipped anywhere in the Cont. U.S. Paypal or M.O. pm me or astrowrench@gmail.com
  5. HueyLewis

    Honda GX140 Help

    I recently bought a kit from NR Racing and it came with a .37 jet. was wondering if I can actually use it with the 140 or if it is overkill. Any input is appreciated, thank you
  6. S

    Honda gx140

    So I have a honda gx140 and the problem is when I try to rev it some times it will rev up but that is rare it usually just kills but it will idle. It idle up and down also. Could it be lack of compression?
  7. roccosbike

    Honda GX140

    View image in gallery View image in gallery 5hp Honda motor. "The Good" it runs excellent, has the throttle hook up already installed. no governor,no oil alert,they have been removed. stock bottom end internals,same stroke as a GX160 just smaller bore. GX160 14cc clone...
  8. iatemeself

    6.5hp clone carb with gx140 tube and 90# main jet

    25$ shipped i changed my carb to a mikuni and this one barely has any use, great power gains, comes with carb spacer and choke lever too
  9. Dragbikemini

    14cc Head off GX140

    GX140 14cc head. Same as GX160 just smaller valves. Wanted to install on one of my Predators but do not have time to clean and get into another project. What you see plus carb studs. Springs are new 18lbs. $35 plus shipping. Located at 10509 Brewster, NY
  10. A

    GX140 parts on Clone???

    Hey guys I have a GX140 laying around and I was wondering if any of the parts on it would be good for my GX200 build. I figured if anything it would just be the head and/or the ignition. I've read that the head doesnt have enough material to open up the ports enough to flow well. What about the...
  11. K

    gx140 not running dont know what to do help!!!!!

    i have a honda gx140 motor oil alert system has been taken off along with the governer assembly. the motor came from a old compresser was not running when i got it. i replaced the exhaust carb rebuilt the head valve job rockers push rods valve lash is set proper along with the timing. i am...
  12. K

    gx140 emulsion tube

    does it make any noticeable gains?
  13. Cotmullion

    Honda gx140 perfomance parts

    Are there any performance parts for a GX140 available? I can only find parts for the gx160 and gx200 ect
  14. M

    Gx140 piston blow-by normal?

    Hello all, I was tearing down my gx140 today to get a a list going for my mini. So I removed the oil sensor and took the governor parts out. I noticed as i turned the crank there was air seeping by the piston into the crank case. i could hear it hissing. Is this normal for these motors or...
  15. GX140

    GX140

  16. R

    Difference Between GX140, GX160, GX200

    Are any of the parts on a GX140 interchangable on a 160 or 200? They're obviously similar, but what are the differences?
  17. X

    Gx140 emulsion tube

    Can any one please tell me how many holes a gx140 emulsion tube is it 8 medium holes, 4 small holes and 2 large holes at the very end? THANKS IN ADVANCE
  18. blkscorpion80

    GX140 air filter

    Will a 6.5 clone air filter and housing fit a Real Honda gx140.
Top