hm100

  1. Steve73

    Hm100 pulse line location

    I've read a few post and searched threads and need to install a pulse line for my fuel pump. Wondering where y'all would drill and tap? Tecumseh uses vacume fuel pump I believe, I also have no experience in this and am learning as I go. Whoo hoo! The tube coming out of the cover below the...
  2. Nesster

    HM100 tecumseh engine swap

    Hi, new comer to the mini bikes world here. I just was fortunate enough to pick up a Super Bronc 2 VT-1040 lately. Played with it a bit and not sure I'll keep the tecumseh (HM100) around for long. Ideally I'd go for a used honda engine, if I can find one, but I heard there are some good...
  3. M

    In what Decade was my HM100 built?

    I am having a hard time determining what Decade my Hm100 was built. Hm100 159182P 9186D Was it built in 1969-1979-1989 or1999 How do you tell when you have just the engine and nothing else. I know it was built on the 186th day shift D but can't figure out the decade.
  4. W

    Tecumseh HM100 valve guides

    What's the best solution for repairing worn out valve guides in an HM100? Tecumseh manual calls for reaming the guides to an oversize and using valves with oversize stems. Those valves are no longer obtainable. I could ream out the guides and install sleeves if I could find some readily...
  5. Cuda54

    HM100 hard starting.

    My HM100 is hard starting when it is the first time. The first cold start take a while even choked once it is warm just a short pull and it fires right up. When it is running it idles fine and has good throttle response. But really hard to get it started the first time after it sets a while. It...
  6. creia

    Tecumseh HM100 needs a carb

    I have a Tecumseh 10 HP HM100 that is missing a carb. I want to try one of those cheap aftermarket carbs. Can anybody provide me with a link to a reliable Ebay seller that you have purchased from before and the carb performed properly? Of course I only want a fully adjustable (both high and low...
  7. M

    Tecumseh star vs. Hm100

    VKE says the star engine and the standard production hm100 are different engines with internal parts that will not interchange. Can anyone elaborate on this for me and is the a production based engines suitable for a star clone build? Thanks.
  8. R

    Copper Head gasket for HM100

    Does anyone know a source for a Copper Head gasket for HM100? I am looking to get a little more out of my old Tecumseh
  9. FirePowerMinis

    10hp HM100 of any use to recreational machines?

    I recall the Star jobs, but does any one run the "regular" ones? I have one on my snowblower, one on a gen-set, plus 2 spares. I think I'll put the Star rod in the 'blower even after price went up on ebay, trim the head and clean up the ports, build a long-tube header. Gennie is getting a...
  10. R

    Tecumseh HM100 part thottle issues

    I have a fresh rebuilt Tecumseh HM100 and a new carburetor and I am having trouble getting it to run correct. The engine has a stock carb/linkage/governor. It starts and idles fine however once under load it bogs hard and sometimes dies. Engine has an ARC rod, valves and seats have been ground...
  11. S

    Tec HM80 or HM100

    Hello, looking for an HM80 or HM100 for a Super Bronc. Anybody have anything?? Thank you!!
  12. Lubbs

    Hm100 tapered shaft to normal shaft

    So I was given an hm100 and it has a tapered shaft I haven't been able to find a replacement for it. Has anyone had luck finding one or coming up with an alternative ? I plan on putting it on my boonie, I haven't had a chance to see if it fits but I think it will.
  13. bart1533

    need advice on hm100 throttle...

    Pick this up cheap ...its a snowblower type engine and I need help on a throttle linkage set up for my super bronc vt 1012... .....any picture I would really appreciate it guys....thanks....:thumbsup:
  14. bart1533

    tecumseh hm100 or 80...

    Need it for my super bronc build...thanks...
  15. toomanytoys

    HM100 with tapered crank

    10 HP TECUMSEH GENERATOR ENGINE Thought about picking one of these up. How difficult would it be to find a new crank for it? Thinking about stuff one of these in my super bronc.
  16. Newoldstock

    HM100 carb serious rework question

    Is there a resource out there I am missing that goes into detail? Not interested in carbs kits, I mean drilling and general madness involved in racing
  17. The_Ruppster_86

    Tecumseh Adjustable Carb

    For sale is my Tecumseh adjustable carb. This carb came off my Tec HM80 engine. The intake manifold is included as well. $35 + shipping through UPS with tracking and insurance I'm located in Duarte, CA 91010 I accept Paypal only. Please PM if interested. Thank you
  18. David wulf

    New carb for my hm100

    Like it says i finally tried the OREGON aftermarket carb for my super bronc . Have been playing around with the stock one for awhile it ran fair but not quite right . Had a bog when I got on it , had to roll into it then it missed up top . Things got worse when i put my new custom manifold on it...
  19. David wulf

    My custom hm100 intake manifold

    My HM100 on my super bronc came with a 5/8 spacer off the engine it was also 19mm inside dia my carb is 26mm so not good . Also the fuel inlet is on exhaust side and the inlet and head pipe touched , so when it got hot motor ran like sh-t . So got one of those drop down type manifolds that turn...
  20. David wulf

    Hm100 carb problems

    Okay got my big block running today . Had carb apart and let it soak in carb cleaner for a week , put it back together and it runs like sh-t . ??? is should i by carb kit or new carb .
Top