horizontal

  1. Aston jag

    "Perfectly" horizontal carburetor?

    Using the intake manifold that came with my Loncin 125cc horizontal four-stroke will result in the carburetor intake end being high, with its bore being at an angle of about 17deg from horizontal. I guess that must be OK because that is the way the manufacturer designed it. Any thoughts?
  2. Ajf

    Looking for a special horizontal shut-off valve

    Does anyone have or know a source for a shut-off valve like the one pictured at the bottom. It is similar to the top ones that are available on eBay but the barb and the threaded part are swapped. Thanks.
  3. myjunk

    2 1/2 hp Clinton engine wanted horizontal shaft

    Looking for a Clinton horizontal 2 1/2 hp engine. I need it for my little gen minibike. Thanks
  4. old shed finds

    Briggs 3 hp horizontal points coil wanted

    Wtb your 3 hp points coil you may have sittin around,, we have lots of engines but no points coil,,
  5. old shed finds

    We have tons and too many horizontal 2-6 hp briggs and tec parts motors

    Anybody need any parts for briggs or tec 2-6 hp engines,, we build and restore go karts and mini's and find we have tons of engine parts,, let us know the part you need,,
  6. JohnnyTillotson

    Horizontal and vertical magneto interchangeable?

    I'm guessing they are but maybe there's something I'm not thinking of?
  7. P

    New Honda GX390 Horizontal Shaft Electric Start

    I have a new Honda GX390 horizontal shaft electric start engine. I was going to mount it on a go cart, but have recently purchased a CJ-5 so my little toys are getting sold. I have the owners manual, factory tools, and some other misc. paper work. I mounted a clutch on the shaft for fit up, but...
  8. F

    HS40 shaft question...

    So ive got a Tecumseh HS40-55565k 4hp horizontal shaft and I decided to build a go kart with it but I looked at the shaft and there is no hole in the end of it like i've seen on all other engine shafts. My question is, would there be anyway to drill and tap the shaft and if so what sizes? Or...
  9. F

    flywheel question

    Will a OE aluminum flywheel off a vertical shaft honda engine work on a horizontal shaft predator 212 ?
  10. gobigorgohome

    Predator 6.5 HP 212cc OHV Horizontal Shaft Gas Engine

    looking for out of state{ gas tank} cap sits to the right of the tank and air filter assemble
  11. J

    Did Briggs make a 28CI Horizontal OHV single?

    Thought maybe some of the Briggs gurus on here mite know if they ever did. I'm thinking I've seen some flatheads but not any OHVs other than Vanguards Thanks Jimmy
  12. wheels1950

    Horizontal engine gokart

    Has anyone ever saw a vertical engine gokart Going to pickup one tomorrow Very small frame THANKS FRANK
  13. 5horsebriggs

    5hp briggs horizontal engine intake and std rings

    Yea I have to rebuild my 5hp briggs and its a 131202 I belive and I'm also intrested in a whole set of both valves if in new condition. I must be able to lapp them too the seat:shrug::thumbsup:
  14. C

    what gasket set for Briggs 3.75hp horizontal FH

    I got a nice, but not running Briggs 3.75hp FH off tiller. Engine model 94202 type 0115 E1 code 990113YB. Partstree gives pn 794209 for the gasket set, but when I look around to buy, its for a vertical shaft engine. Sears gives another pn 495605 that seems OK. Would like to buy from...
  15. M

    Typical Crankshaft Step-up for 3/4" Horizontal Shaft

    Hi all, I'm retrofitting a piece of equipment to my utility engine for my mini bike and I've noticed that I have three different types of crankshafts on my three engines. The part I'm concerned with is the increased diameter step up that occurs on the crankshaft right before the 4 bolt mating...
  16. 5horsebriggs

    verticle to horizontal

    Well can a verticle shaft enge be changed to horizontal... is it hard?
  17. Pasta

    Briggs 5 horse horizontal

    Anyone know the torque value for the connecting rod bolts? Was it 35 in/lbs? I'm trying to remember from the 70's, but that was a long time ago. LOL Thanks in advance. George
  18. B

    manual clutch for horizontal shaft engine

    Hi all. I used to post on here quite a bit a few years back under the username "briggsscooter". I forgot my damn password and no longer have the email account that that user name was linked to. Oh well. I've surfed the internet and this forum and cannot find info on any manually operated...
  19. Pasta

    Briggs 8HP horizontal shaft engine

    I have a Briggs 8HP horizontal shaft engine from a generator. The end of the crankshaft is tapered, and there's no slot for the key. While I have the engine apart, I might as well replace the crank in case I ever want to install a clutch on it. What should I expect to pay for a good used crank...
  20. T

    converting vertical shaft to horizontal

    does anyone know how to do this? theirs a video on youtube but i was wondering if anyone has used a mower engine for a minibike and how well it works.. if you guys have any advice please help. im interested in doing this but im not sure how good it will work. if you guys have any pictures...
Top