installing

  1. DeadPixel

    Installing GX160 lifters in the GX200?

    So I am getting to the point soon were I will be buying lifters for the clone I am building and see that the 160 lifters are a little lighter. I also noticed that the lifters are only guided by the block with no inserts so its straight on aluminum. Guessing the lifters are shorter and am...
  2. M

    installing a clutch on a keyless shaft

    Gents any tips on installing a clutch on a keyless shaft? Have a 3hp briggs from an edger but it does not have the key on the shaft.
  3. Timmmaahh

    installing 212 hf preditor on db30

    not as bad as it seems,but you need to weld a bit.buy a motor plate with curved ends its made to do this swap,but no one says so.cut old motor plate off,weld on new one.cut a pie shape on loop that back fender bolts to and pull toward back 3 inches and weld up.now the engine fits,its a ball to...
  4. A

    installing new tire

    whats the best way to put a new tire on a rim? i have 4.10 x 3.5-6 tires for a 6" rim. i got them off fairly easy, now im having trouble getting the tire started on the rim. i have a set of tire irons thank you for any ideas
  5. J

    How To: Installing Predator motor in Rupp Blackwidow

    I just finished installing a harbor freight predator motor in my Rupp Blackwidow. I saw a few people with pictures of it done on here, and ive seen a couple people asking about it, but didn't see anyone actually talking about what it takes. Its pretty simple so I thought I would go ahead and...
  6. 6.5hp Shinebox

    22mm mikuni Carb on Predator 212 hemi

    How do I install this puppy? Carb came with some screws / bolts... Washers... Can,any one give me some kind,of guide to installing carb on the head. I have everything I would need to install Your advice is appreciated I'll post some,pictures if I can
  7. J

    Installing 1.1 ratio rockers

    Will I new to change anything if I put the champion rocker in a box stock project, Also can I run the rockers with the stock studs or do I have to use the ones the rockers come with
  8. ogygopsis

    Installing Spacers Properly

    The placement of a spacer between the right and left bearings of a wheel hub is an important detail that a lot of people don't pay much attention to; much less take the time and effort to install properly. If you want your wheel bearings to last; a spacer is an absolute necessity. If the...
  9. R

    Help with installing wheels

    Hey So i'm trying to build my go kart . i think i'm miss someting :out:. I'm installing the wheels to a dead axle. So all hubs have bearings. If i tighten the nut too much than the wheels don't move as freely. I'm afraid that the nut's would loosen on it's own. What i'm i...
  10. buckeye

    Installing rings

    Well, I am stepping into parts unknown.:laugh: I am putting new rings in a little 5hp Briggs. Do you have to use one of them fancy ring expander tools or is there a trick to this???
  11. Clayon

    Installing Billet Lifters on a 5hp FH

    I have heard of something having to be done to the lifter area when using billet lifters, what has to be done? and would I have to do any mods at all if I am using stock length billet lifters? and at what point should you use billet lifters? :shrug: Thanks.
  12. Clayon

    Installing new pistons

    Hey guys I have a couple questions about installing new pistons into my 3hp I/C Briggs. The cylinder is honed, I cleaned it out really good afterwards to make sure there are no filings or anything from honing, and I have the rings installed on the pistons like I'm supposed to, and I've filed...
  13. old-timer

    Installing drum sprocket help needed

    I'm installing a new drum brake sprocket on a new Azusa TriStar wheel. Can someone walk me through what I need to do and how to go about it? Do I bolt the new drum sprocket to the wheel using the stock bolts that came with the wheel? They don't even look long enough. Then when I install the...
  14. texasfabguy

    Installing tubes

    Got some new astro wheels and trying to install tubes. But here's the problem,the tube seems like the inner part is to small for the rim. The tube size matches the tire size but I can't get it to stuff in the rim between the halves. Any tricks?
  15. trailramdan

    installing a lighting coil

    need tips and info on installing the lighted parts on my new motor. ive never done this before so is it easy enough to do on your own or better off taking to get it done? also where are the wires i need to run out so i can add the plug for the headlight etc...also is is possible to not run the...
  16. Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.
  17. Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.
  18. Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.
  19. Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.
  20. Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.

    Installing valve stems and mounting tires.
Top