removal

  1. E

    Comet Series 40 Belt size and removal question

    I'm wanting to remove this from my Super Bronc 2 VT-1040... I removed the bolt at the end of the engine drive shaft, but the drive 'clutch' isn't budging. Am I missing something? Do I need a grear puller or some other tool? Also, the belt that came on it is a NAPA 25-07800/24308 5/8" wide...
  2. deezildennis

    Jacked up Tecumseh ohh60 (Governor removal gone bad) Need help

    One of my Buddies bought a new tecumseh 6.0 powersports engine a while back and decided he didn't like the governor after he broke it in. The engine ran perfect before but not so much afterwards. I brought it home to keep it from going in the scrap pile. It literally has like 5 hours on the...
  3. R

    MBX10 clutch cover removal

    This may seem like a stupid question, but I don't want to mess up the mbx10 (got for free) my 9 year old son is so proud of. I've removed the 2 bolts by the clutch, but can't figure out how to remove the screw near the rear wheel. I can feel the screw turning but can't get my fingers far enough...
  4. G

    Tecumseh clutch removal

    How do I remove the Max Torque clutch from the 3.5hp Tecumseh motor? It has a grease fitting and bolt on the front of it. I can't seem to remove it. The clutch keeps spinning.
  5. drenchedgremlin

    stubborn clutch removal, need help

    I am trying to get this clutch off. 2 problems, No idea how to get that key out, & the allen bolt is stripped. What would you guys recommend.?
  6. S

    briggs 5hp governor linkage removal inside the case

    I have a old school 5 hp with the linkage arm rod going into the block do i need to remove the side case and remove the nylon gear off the cam and plug the hole or just leave it in with the outside arm off?.and run it....thanks
  7. Sprocket86

    Tec HS50 upper fuel tank bracket removal

    Going to be removing the upper fuel tank bracket from my HS50 engine. When doing so, do you reuse the steel spacers that go under the bracket for the head bolts? I would think you would remove them if not using the engine mounted fuel tank, but then would you need shorter head bolts? Thanks.
  8. C

    Governor removal??

    I have a coleman ct200u with the stock 6.5hp clone in it. I added a kit from hotrodminibike .com, with a K&N filter, .35 jet, and racing plug. Any good directions for governor removal? I understand its a "risk" and can be "dangerous", but wanted too see if anyone did it and how it turned out...
  9. W

    jackshaft removal and flipping clutch

    Hello forum members. New guy here and wanted to introduce myself. I have a Coleman Ct200u and this is my first mini bike:scooter: It's fun as heck and has plenty of torque to satisfy my current needs but I would gladly trade for more speed. Reading about mini bikes here is what made me...
  10. manchester1

    Tecumseh muffler removal help

    Trying to get this muffler off. Is the nut reverse threads? This has been soaking for months and I still can't get it off. Any help appreciated. Thank you.
  11. SIDEPOCKET

    Snow Removal... (for us lucky ones that get it) What Do You Use? Show n' Tell

    Just thought I'd pose the question, "what do you use for snow clearing?" I was thinking about the other day while cleaning up our 3rd big snow dump this winter... Feel free to post up some pics of your tractors, snow plows, snow blowers, or ...really fancy ...shovels? :shrug: Here's what I use...
  12. gwoods27

    HS50-67023 Crank Case Cover Oil seal removal

    Anyone have some advice on removal of the Crankcase Cover oil seal on an HS50. I dont want to do any damage to the crank shaft. Trying to get the case cover off to do a rebuild.
  13. manchester1

    Alsport front wheel removal

    How the heck does the front wheel come off.:out: The 2 bolts are only 3/4" long, not like a axel bolt. Looks like some sort of a shaft. Help please.:bowdown:
  14. james ackerman

    Decal removal for saving? How to!!

    I have a decal on this gas tank I'm restoring and I would like to be able to peel it off without damaging it so I can get it replicated. Just trying to peel it doesn't work. Does anyone have any tricks to the trade or hints on how this can be done. Also who knows someone that is able to...
  15. BBQJOE

    A somewhat epic 4th of July pack rat nest removal. (Arizona style)

    https://www.youtube.com/watch?v=DqtxmAebe80
  16. B

    Tank removal 212 predator?

    Is there anything I need to do to remove the tank to run a frame mounted tank on my 212? Thanks.
  17. jays0n

    Hemi Predator Governor removal parts list

    I have a Hemi Predator on my DB30 and have decided it's time to remove the governor, low oil sensor, etc. I've done tons of searching and can't seem to find a definitive parts list anywhere. I know that's likely because there are 100 ways to accomplish this. The only thing I don't really know...
  18. M

    Predator 212 Governor removal now will not start

    Hi I just removed my governor on my 212 with the basic stage 1 upgrade kit. I removed the low oil sensor, got the washer behind the governor, lined the dots on the cam up, did all the wiring correctly and checked the plug. The motor would not start so I took off the OHV cover and the engine...
  19. 2SlickNick

    Need stump removal / ID

    I am stumped and having a hard time Identifying this MiniBike. Need ID on the green/black. https://www.youtube.com/watch?v=L0FQMDDxSg4
  20. D

    Predator governor removal question. Should I do it or not?

    Hi. I have the Canadian version of the Predator 212cc engine, the PowerFist 200cc 6.5hp engine. I am replacing the plug with the longer hotter one from GoKartsUSA.com, plus the upgraded cone airfilter and adaptor, their straight 1 inch exhaust pipe and screw on muffler, larger size 34 carb jet...
Top