searched

  1. B

    Searched and searched....looking for an easy answer regarding timing and arc flywheel

    Hi Folks, I DID search for at least an hour....so if I missed it, pardon the ignorance. New non-hemi HF predator engine. New Arc billeted flywheel (non adjustable 8degree advanced) Do I need to "adjust" timing after installation?? Or can I assume timing is "on"? Mod 2 cam BTW. Thanks!
  2. xr7gt

    Tote Gote fest Utah 2015?

    Are there any plans for a get together this year? I searched for information but couldn't find anything current. Anyone else in Utah want to meet up?
  3. mariner12

    9 tooth clutch sprocket

    I'm in need of a 9 tooth clutch sprocket preferably for a Hilliard clutch. I need more gear ratio but don't have room for a taller drive gear. I've searched and can't find one. Any help would be appreciated.
  4. buckeye

    1970 Scrambler Torque Converter Assembly

    Here we go again with dealing eith TAV, with a feeble mind.:out: Of course at the time of disassembly my mind wasn't feeble and I thought for sure I would remember how to put it back together, so didn't take pics...:confused: I have searched diagrams and still can't figure out how to...
  5. capguncowboy

    So, want to take a stab at it?

    I recently bought a bike. It came today in the mail and this part was inside. I'm not sure what it is, but I'm nearly certain it's not a mini bike part. It's about 22" long from end to end, the straight pipe is about 19-1/4" long and is 1" OD. The end with a fitting is 2" OD and 1-3/4" ID...
  6. D

    Removing Fox Trail Tramp bars

    How do I get these handlebars off? I figured out the forks and the fork lowers, but I can't figure out these bars. I wonder if they're just rusted in the forks? Anybody got any good pics or tips? I've searched YouTube, but I couldn't find anything. I just want to paint or powder this thing...
  7. Commonrail

    5hp Briggs and Stratton flat head questions.

    I recently purchased a B&S 5hp flat head and it came with a different carb setup. I would like to replace it with the stock setup that has the fuel tank under it. I have searched and searched with nothing found. There were a few on eBay and they looked as if they were sitting in salt water for...
  8. D

    Real world experience with hydraulic disk brake conversion on rear.

    I've searched and searched with the search tab in a few sections on OldMiniBikes but cannot find any info on this subject. I am looking at using the sprocket for the brake disk but need a good universal type caliper and master cylinder. Ive seen some on doodle bugs but Im unsure how thick of a brake disk...
  9. Txpowdercoater

    BIg Cat wheel bearings? I have searched and searched

    to no avail. I have looked at mcmaster carr and motion, still havent found the bearing with the flange thats needed. I know somebody has a real part number that works. I googled the numbers on the bearings in it now and found zippo, nada, zilch. they have 64f and sst on 'em and are 1" id x 2" od.
  10. Jamie1972

    I searched the internet and found NOTHING!

    Can anyone tell me the base line settings for a tecumseh 3hp carb.? The engine is in good running cond. the carb has been diassembled and cleaned. I need to know the idle screw, air/fuel mixture screw and wide open throttle screw on the bottom of the bowl settings. Thanks! OH...Im...
  11. smokinsmo

    searched for 2 hours..No luck

    I have an engine that i need help with ID., well not really ID but some more info like what cc or HorsePower any info is appreciated. The plate on the engine reads ::: Power Bee, Chrysler outboard corp, Two-cycle engine. Engine Model 82030 Engine Serial 7432 Hartford, Wisconsin USA Thanks !!
  12. manco12

    Checking chain tension - I've searched

    When you check chain tension, say you want 1/2" - 3/4" of play, When you measure the play, how hard do you push on the chain? It makes a big difference if you just kind of lift up/down or actually put a little bit of force on it. Because when its about 3/4" when you apush a little it still...
  13. Hellaslow

    I searched with no outcome...

    can someone please post a link to lowering the fenders on my db30? thanks...
Top