setting

  1. 125ccCrazy

    Need some help on setting up a BB Tec throttle linkage

    I'm putting some factory style minibike carb linkage on some engines I'm building and I'm having some issues with the linkage rod between the carb and the governor arm, the big [ shaped arm... the issue is the throttle arm, none of the holes are positioned where I can get a pull from the...
  2. jdogg

    Bead setting grease!!

    Took my 6'' Snow Hog tires to my local tire shop to have them set the bead on one that was distorted as I tried the ratchet strap and starting fluid trick to no avail!! I expected him to hit the bead with the usual precompressed tank to do the job but the new guy suprised me with something I...
  3. 125ccCrazy

    new 5/8 centrifugal clutch

    new, never used...may have a few scratches and some dust from setting in the parts box in the attic,, $10 plus ship
  4. R

    new carb low speed setting

    does anybody know what the low speed setting should be for this carburetor? not familiar with tecumseh carburetors. this is for a 6.5 power sport ohh65 71707c. thanks!
  5. T

    need help with setting the governor or how does it work?

    hello, i have a tecumseh model H35-457 66Y 3.5 hp mator and need help with getting the throttle to work right, i have all the correct spring and governor lever, but the problem is that the throttle stays wide open now, it wont go back to idle speed, what makes the governor lever go back so it...
  6. K

    Need help setting idle speed

    Trying to get my sons' go kart up and running. I don't have much experience with these karts, so bear with me. With help from the kart section on this forum, I was able to replace the clutch assembly. But now the issue is that the engine just won't settle down to a good idle. It's revving...
  7. K

    Need help setting idle speed

    Trying to get my sons' go kart up and running. I don't have much experience with these things, so bear with me. With your help, I was able to replace the clutch assembly, and it's great. But now the issue is that the engine just won't settle down to a good idle. It's revving hard at all...
  8. skidoo50

    Initial carb setting on 5hp fh

    What would be a close start up setting on the carb screw? The carb is a pulsa jet.
  9. J

    Setting up a band Brake on a Trailblazer

    Was wondering if anyone has info on setting up a band brake. I have the band brake bracket, the drum and brake band and cable. The brake lever seems to be missing something to attach the cable to and on the other end there are parts missing as well. Does anyone have a drawing of what is...
  10. Paticus

    Setting up Live Axle

    Do Live axles require threads and a nut on the ends to keep everything in place or can this be achieve with a bearing set screw and a lock collar?
  11. M

    Setting a Tecumseh HS 40's Timing???

    Does anyone know how to set the timing on a Tecumseh HS40. I took the entire engine apart (model 55388c) to restore it. I installed new points, condenser, ignition coil and cleaned the lighting coil. Obviously getting the timing set correctly is the next step.
  12. boatguy

    Tilly Carb Setting

    I have a 5hp Briggs with a pipe, ARC rod and a large Tilly carb. The bike runs fine but when I stop it gas runs out of the carb. What settings (number of turns) should I be using. The motor has a Walbro pump on it but a stock cam--is the cam the problem or carb settings? Thanks Bill.
  13. J

    stock carb setting

    The honda gx200 i got wont idle. I can keep it going if i stay on the gas but it wont idle. Can anyone tell me the " starting point" for the adjustment screws? idle, and air/fuel mix.
  14. M

    Setting fire to a Rupp TT500

    Ok if you rupp guys don't sell me some parts for my TT500 I am going to set it on fire and video tape it and post it here. :thumbsup:
  15. mr.modified

    GC160 setting valve timing

    I was wondering how to set the valve timing on a gc160. I was taking one apart for the heck of it last night and I didn't see any marks on anything. Anybody know what the deal is?
  16. M

    point setting 1959 3HP

    I put in my new points and condenser last night and I am still not getting any spark. I still have juice at the plug wire but no spark coming from the plug. The plug is new so I know it is not that. Do I just need to set my points on my engine? I have never set the points on a small engine so I...
  17. creia

    Tecumseh OHH60 - Governor setting

    As you can tell by my previous questions/posts I am new to these engines, and learning alot from the collective knowledge on this forum.:001_tongue: This is on a 2 year old 6HP engine: I have NO intention on removing the governor, however I do want to make sure it has the PROPER...
  18. vette66_00

    Video: Replacing Valve spring and setting lash 6.5 hp

    I did a little video on replacing a Valve spring with a 18lbs one and setting the lash. Video is only of the exhaust but its the same way for both intake and exhaust. Should be good enough to get most people though doing it. LMK if you have any other questions or suggestions to improve. I think...
  19. JayQuan

    Need Help on setting up my throttle

    I need some advice on how to set up a throttle on my clone, if you guys could post some pics up of what you did that would be great. thanks -Jake
  20. B

    setting valve lash

    I know it may be a stupid question, but i dont want to screw anything up. How do you set the valve lash. Lets say i put my new springs in and the valve lash is at .008 and it needs to be .002, how hould i change that. that is hypothetical.
Top