stay

  1. W

    I should stay warm hunting this year

    I made this blind out of sheets of 1 5/8th inch structural foam with 1/16th sheets of a thermoplastic laminated to both sides. It is rigid enough to walk on supported 4 foot apart. The blind has removable Lexan windows. A 4 by 10 foot piece of this material weighs less than a 4 by 8 piece of...
  2. Harleys Papa

    Cable Stay

    I need a cable stay like this one, if you have one PM me and I would be more than happy to buy it :thumbsup:
  3. markus

    Early Caper cycle brake stay?

    working on a 1961 short frame Caper roadrunner/falcon, Tyring to figure out what prevents the brake plate from rotating. Looks like in the brochure that the brake arm almost rests against the top of the axle mount? In various pictures of actual bikes online though the arm is in different...
  4. toomanytoys

    I need to stay away from here

    I got bored the other day and started browsing again. Started reading David Wulf's H50 hop up thread, reading about a couple other people's project. I hate all of you. Now I have in my head to dig out my H50 from the shelf, and my 69 Rupp frame, and start building another bike. I...
  5. F

    Predator 212 won't stay running...

    Right now, I can pull the starter, then I have to give it throttle to keep it alive. If I let go of the throttle the engine will kill itself. If I release the choke, the bike starts moving BUT when you let go of the throttle, the engine should idle, but it doesn't. The engine just dies. Has...
  6. cpu77

    I bought a old style Doodlebug and want carb linkage....

    i bought a bike that has had some carb linkage engineering. I would like to buy all the springs, linkage bar and cable adjuster. I wanna keep the 97cc engine for my 7yr. The carb is getting replaced as well. The choke is wore out and vibrates back and forth. I currently use a spring to...
  7. Acolytus

    Carburetor help!

    Hey guys I just cleaned out my carburetor for on my scat-cat mini bike which has a 3.5HP Tecumseh motor on it (Tecumseh/H35-45621S). As I was about to connect the fuel line, I noticed when I give it throttle, it (not sure what the name of the part is) doesn't come back to it's starting point...
  8. V

    Newb from Indiana

    Hey everybody, My name is Brandon 31yrs old married father of 4, union distiller, back yard gear head fabricator. Been building air-cooled VWs since I was 15, have had over 150 vehicles in the past 16 years. I guess you could say its my vice, wife hates it. But i tell her its better than...
  9. J

    You ALL missed out on this Mike Bike......

    Saw this in the cl ebay forum a while ago. Sat ther, sat there. Yes it's in Maine.... Yes I'm 'M in Maryland. Talked guy(for a fee) to deliver it 4 hours away to my dad...... Motor is off because he had a 5hp on it that I cut out of the deal. It is all otiginal... And will stay that way.
  10. P

    Can stale gas cause this situation...

    I have a fairly old Craftsman snowblower (single cyl., 17.5 HP OHV) that refuses to stay running... I had to replace the metal connector from the plug wire to the plug (became damaged) since I removed the plug so many times to check its condition or to unflood the cylinder. Basically, I...
  11. R

    Think I'm gonna stay up till midnight...

    and see what happens when the date turns to 9/1/13 and my supporting membership expires.
  12. F

    Won't stay running when throttle is applied . .

    I bought a used Baja Warrior 200 and when I first got it, had a little problem with it, but after it was left running for about 5 minutes would work just fine. It ran completely out of gas, was filled back up, now will not run after any length of time, nor will it crank back up immediately...
  13. Furious D

    HS-40 wont stay running

    I usually try to figure out these problems myself, but after 2 days of working on this problem I am stumped. I have a early 70's HS-40 that was rebuilt around 7 years ago but never started. I changed the oil, checked for spark and put some fresh gas in it and nothing. Found the timing was...
  14. C

    Chain won't stay on

    I'm have problems keeping the chain on my old mini Bike. Replaced the wheel bearings and it looks like it is in line with the clutch. The rear sprocket my have a little wave in it. When I spin the rear wheel with out the chain it is smooth but with the chain it has a little tight spot. Maybe new...
  15. M

    wont stay started

    My honda on runs with starter fluid what's a mini biker to do?
  16. SimpleTom

    I would stay away from bidding on this one

    Look familiar?.... VINTAGE MANCO MINI BIKE FRAME FORK WHEELS TIRE GEAR BRAKE ROLLING PROJECT START | eBay See this thread from member "Timmahhhhh": http://www.oldminibikes.com/forum/what/61582-mystery-mini-bike.html
  17. T

    my mini bike wont stay running

    i have a 4 horse techmesh engine but i spray starting fluid in the carb it fires up but then dies in about 5 seconds... Any suggestions????????:shrug:
  18. nitrosteve

    clone wont stay runing

    i put a header on it and now it will idle and throttle up but when i let off it dies
  19. mac350

    wont stay running

    i have a 5 hp Tecumseh. it was running when i got it. it sat for a few years till i found a frame that i wanted to put it on. know that it is in a frame i cant get it to stay running. it will stat with the spray starter but just stall like it is not getting gas. i swapped out 3 carbs and still...
  20. P

    DB30 won't stay running (just out of the box)

    Just got one for the kids, I haven't messed around with one of these in a long time. After finding a suitable oil plug I go to start it and it doesn't want to stay running unless I hold it on 1/4 throttle. I'm thinking it might just be the idle but I'm not sure. Is there something I should...
Top