Search results

  1. Kustomtoyz

    Go devil gas cap or complete tank NEEDED

    My Go Devil has been sitting on the shelf for several years now... I need a friggin gas cap. Know of one (or a complete tank) let me know! Thanks!
  2. Kustomtoyz

    Age of members on here?

    Big FIVE OH in less than a week... If I could just remember all that I know, I'd be a genius.
  3. Kustomtoyz

    Tecumseh HELP 11hp carb starving for fuel

    Good news! I found the problem... I re-cleaned it and again found nothing BUT I found that the center tube that likely acts as a main jet (does not have a real 'jet') was stuck down into the bowl. It has a spring in the bottom of the bore (in the plastic float bowl). When I pulled the tube...
  4. Kustomtoyz

    Throttle control?

    I've got that same throttle on two of my bikes. Works great and Hent's right, the bigger grip is a plus...
  5. Kustomtoyz

    Tecumseh HELP 11hp carb starving for fuel

    Heck that's not rude... With all the plastic I knew it was crap. I have a Walbro PZ30 but I need to play with the jetting. I THOUGHT I'd put the stock carb back on and connect the governor just to get a base-line on how it was running before tuning the Walbro. I knew I'd end up re-cleaning the...
  6. Kustomtoyz

    Tecumseh HELP 11hp carb starving for fuel

    Just about done with the build and now I'm having problems with the stock carb. This is a brand new (old stock) motor. Ran fine about a month ago but now it only idles. Any throttle with the choke off, it trys to die. Choke on, rev's up... I've never worked on this (new) type carb with the...
  7. Chopper

    Chopper

    Used the stick-on chrome 'vent' to cover unused factory holes in the blower cover. Little cheesey but not too bad...
  8. Chopper

    Chopper

    12v elect start!
  9. Chopper

    Chopper

    8" wide rear tire
  10. Chopper

    Chopper

    Hand fab'd brake. Springer front (BMI)
  11. Chopper

    Chopper

    Custom intake/filter
  12. Chopper

    Chopper

    Sprung seat, hand fab'd seat bracket & fender supports.
  13. Chopper

    Chopper

    Hand fab'd stainless 1-1/4" exh and SS battery box.
  14. Chopper

    Chopper

    Comet Maginum 44C / 40 clutch.
  15. Chopper

    Chopper

    95% complete! Almost 8 feet long with a Sportster tank and forward pegs.
  16. Kustomtoyz

    GO DEVIL gas cap needed!

    If anyone has a Go Devil (folding minibike) gas cap or a tank/cap you'll sell, message me! One just sold on eBay about a week ago and I missed it... Still pissed.
  17. Kustomtoyz

    BANNING members from forums

    You gotta be S****'n me? Banned for that? Wouldn't go back anyway. No doubt all forums should have some rules for overly offensive behavior but that seems a bit overly holier than thou. I wouldn't loose any sleep over it. Sc**w'm.....
  18. Kustomtoyz

    Manco steering (headset) bushing source?

    Tractor Supply also has the brass bushings. I make my own from brass or bronze if the size is oddball. Take a chance you can modify one the standard 5/8 from Home Depot, Lowes, Tractor Supply etc. Thats the best price. All else fails, message me. Good luck! Don
  19. Kustomtoyz

    GO DEVIL parts needed!

    I picked up (after looking for several years) a complete Go Devil minibike. I need a tail light complete or at least a lens, I need a flilter foam (can make one if I have no luck). I also need to find a gas cap and figure out new steering head bearings. No idea if thats all I need... Just...
  20. Kustomtoyz

    i got 10 gallons of 100 octane low lead... can i reduce that to 87?

    I've got a buddy who started out back in the old days in top fuel "Nitro" drag racing and now into Mototrials and the GAS GAS Tech guru - He says the higher the octane, the SLOWER the burn which is why it helps with detonation. I'm pretty sure the gain will not be noticed at all in a motor that...
Top