Search results

  1. V

    Baja MB 200 Rear Sprocket Question? Upgrade?

    Karting Distributors in Keller Tx. Phone (817) 482 1600 has a 60 tooth sprocket that replaced my factory one on my MB 200, it fit absolutely perfect, Call them and ask for Aaron.
  2. V

    Baja MB 200 Rear Sprocket Question? Upgrade?

    Call me , I have the answer ! (409) 283 7119 I just bought one that is a perfect fit.
  3. V

    Baja MB165

    I have the part numbers for the mb 200 and a great source for these parts. Call me 409 283 7119
  4. V

    Predator used crank 3/4" keyed & threaded needed !!!

    Thanks for your help, I found an old engine, cut off the end of the crank and fit just perfect.
  5. V

    Attention !!! all Fat Tire bikes, Trailmaster, Baha, Bigdog etc. WOWWWW

    Look at my latest post for your remedy on the perfect sprocket. Call me if I can help? (409) 283 7119.
  6. V

    Attention !!! all Fat Tire bikes, Trailmaster, Baha, Bigdog etc. WOWWWW

    Karting Distributors in Keller Tx. Phone ( 817) 482 1600 has a 60 tooth sprocket that replaced my rear sprocket on my MB 200, it fit absolutely perfect. Call them and ask for Aaron.
  7. V

    Comment by 'v8music' in media '100_5895'

    Tons of fun !
  8. V

    Predator used crank 3/4" keyed & threaded needed !!!

    Call me (409) 283 7119 if you will. Thanks
  9. V

    Predator used crank 3/4" keyed & threaded needed !!!

    Yes , Any suggestions ???
  10. V

    Can you buy 3/4 shaft EXTENDER with center hole & keyed ?

    Gumpit, Where can I get more info on this ? Dimensions ?? Looks as if I use two of them and cut off the shoulders it would be perfect.
  11. V

    Can you buy 3/4 shaft EXTENDER with center hole & keyed ?

    I am using the last 3/8" of the shaft for the torque conv hub, leaving 1 1/4" with no shaft or key.
  12. V

    Can you buy 3/4 shaft EXTENDER with center hole & keyed ?

    I need 1 1/4" more shaft length.
  13. V

    Predator used crank 3/4" keyed & threaded needed !!!

    Would not have to be a predator I guess, just thought if the threads matched up it would be nice.
  14. V

    Can you buy 3/4 shaft EXTENDER with center hole & keyed ?

    Not yet, but did post that I need an old crank and I don't a mean a wife.
  15. V

    Predator used crank 3/4" keyed & threaded needed !!!

    I only need approx 1 1/2" of the very end of the shaft.
  16. V

    Can you buy 3/4 shaft EXTENDER with center hole & keyed ?

    Need longer shaft on the 212cc, The splined hub driver only fits on 3/8" of the end of shaft.
  17. V

    can't get this briggs started. help?

    I have had spark from a plug but would not crank. Put in new plug and it ran like new.
  18. V

    Low End Power?

    You must read my post shown under "engine modifications" on this site. I now have the best of both worlds, torq and top speed. Call me if needed. I will give you the phone number to call !!! I ordered sprocket and 36 hrs later it was installed and I was climbing the biggest hills I could me and...
  19. MB_200_Beast_

    MB_200_Beast_

    Trailmaster MB 200 Beast 60 tooth sprocket
  20. MB_200_Beast

    MB_200_Beast

    Trailmaster MB 200 Beast 60 tooth sprocket
Top