Search results

I have a speedway widow maker with the sachs 80b engine on it. the engine runs great, however the carb gets loose after running for a few minutes. is there a fix for this, or maybe a different way to mount the carb. any help or suggestions are welcome. Thanks !!

wanted sachs 80b header pipe for a widow maker. will trade parts for it, NOS in box piston, or maybe a fuel tank. PM me let me know if one is out there. thanks.

Need sachs 80b exhaust header pipe for widow maker. I have some 80b parts to sell or trade.

Hello out there in mini bike land. Is there anyone out here that knows how to work on 2 stroke crankshafts? Or better yet are there any 80b parts out there that someone would be willing to part with? I have 80b parts to trade/sell to get to my goal-a running engine. I have 2 cranks that need...

sachs 80b flywheel side crank has slight bend. any way to fix this? mags rub on coil.

Sachs 80b has anyone had one these with a bent crankshaft on the flywheel side? if so can they be straightened? the bend is slight enough to have the flywheel magnets rub on the coil. any help or suggestion would be appreciated. Thanks Pete also on another note looking for a carb gasket set or...

looking for a lighting flywheel, some fin damage OK will pony up for the right parts. tecumseh AH817 MB.

picked up a red MTD, looks like a desert fox, has a AH817 engine, anyone have parts for this motor? I need a lighting coil flywheel, or not, something that fits/works. bike is 99% complete. I would hate to have to put 4 stroke on it. looking for help or leads.

Hello everybody, I have A sachs 80b that wont start. It did once and died out, now nothing. has good spark, clean points, I even removed the motor and turned it upside down to get excess gas out of it. not flooded. the carb is NOS, so is the motor. i am stumped. could the condenser be bad? It...

Hi everybody, I need a little help here, or suggestions. I have a speedway greenhorn, has 14 inch wheels, I am running the stock T C driven with a 20 series driver. I am using a comet 3/4 belt. the belt fits great in the driven, I'm running a 7hp tecumseh , mild cam and large bore float bowl...

Hi everybody, the season is near. looking for a motor mount for the sachs 80b, widow maker. theres gotta be one out there somewhere. thanks for looking.

WTB sachs 80b widowmaker engine plate, front exhaust pipe, and a new style clutch. Thanks Pete.

wanted , sachs 80b engine plate. new style clutch, also, I have seen an engine plate behind the PTO drive??, any help would be great. thanks. PM me Pete [ATTACH=CONFIG]939 have no idea why pics come out sideway??

It is a pile of Rupp, just what I wanted:doah: Well its time to dismantle, and see what it is, and go from there. Whoo Hoo!!

just picked it up today. its 22 inches long and has spark arrestor, and number on it.

I have 3 tecumseh connecting rods, one is a bone stock H50, the next is a motorsort H50 rod, and the other is ? poss star 10HP, it takes bearings. Help is needed. Thanks.

looking for a 14 inch wheel speedway frame and gas tank, front end not needed. roch ny area.

just acquired, are parts available? has 15 inch tires.

just acquired, a Rupp. never had one of these. it looks to be all original, and complete. looks like it was rode a few times, then put in the barn and forgot about. Poss, 1975 ? the last of the Rupps ? What to do next, clean and run, or complete take down for rebuild ? the tires seem to be the...

Hi everybody, I have 2 comet drivers. one has steel weights, the other has zinc or aluminum. is one better than the other? or do they engage at a different RPM? Or is there no difference? I recently got a set of lower RPM engagement springs. Im trying to lower the engagement off idle, Im...