Search results

  1. C

    Gilson/Widebody

    Torque converter model, belt final. H50, full lighting, rechargeable battery. Heavy bike, more show than go. Used for parades (governor/gearing set for low RPM). $1000, pick-up only Hermosa Beach, SoCal.
  2. C

    Gilson/MW XE525

    Two-speed model. Lighted H50, period-correct Mesinger seat (OE seat incl.). New carburetor/air cleaner (OE parts incl.). $1250, pick-up only Hermosa Beach, SoCal.
  3. C

    Gilson/MW V424

    Torque converter model. Lighted HS40, period-correct Mesinger seat (OE seat incl.). Unrestored w/some paint touch-up, new carburetor/air cleaner (OE parts incl.). $850, pick-up only Hermosa Beach, SoCal.
  4. C

    WTB- Riverside Tire

    Need one 5.50/4.30-6 Riverside tire and the tube.
  5. C

    Mustang Trail Machine- Looking for Restorer

    I am looking for an individual or shop, located in Arizona, who had restored (within the past few years) a 1961 Mustang Trail Machine with an 8.5HP B&S. Sound familiar to anyone here? I know little about these Mustangs but it appears a 5.75HP B&S was OE so this fully-refinished example is a...
  6. C

    WTB- Sebac Parts

    Lower tapered tube and mount for 11.75" shock needed. Also look'n to buy NOS or excellent/used pairs.
  7. C

    WTB- Crankshaft Drill & Tap Guide

    3/4 version. Purchase or rent as I will never use it after this engine.
  8. C

    WTB- Sebac Shocks/12in

    Anything off a Gilson, Wards, AC or possible others w/12" eye-to-eye dim..
  9. C

    WTB- Taylor Model #100 for HS40

    PM a photo of what you have to offer.
  10. C

    WTB-Headlight Bracket/Tail Light for Gilson/Wards/AC

    Need Speaker headlight bracket and complete tail light assembly. Might consider Arctic Cat parts...
  11. C

    Gilson/Sebac Shocks

    Regarding the Sebac rear shocks for the high-line Gilsons, why are the springs installed upside down on every single photo I've ever seen? Progressive coils start out resilient and eventually become "near-solid" or flat in response. With that said, coils at the bottom are spaced far apart in...
  12. C

    FS: NOS Tecumseh H60 Engine w/Series 30 Driver

    Model 75482S-2153D, paperwork included. Series 30 GTC driven unit. Both new. $465 shipped.
  13. C

    WTB- Gilson/Wards Survivor

    Looking to add another complete Gilson or rebrand: Gilson 180, 185, 700, 701, 13966A, 13976A, 13977A Wards 323, 424 Complete or near-complete examples only. Top money paid for unrestored w/OE engine running or not. Must be able to disassemble/box on your end and transport to a FedEX...
  14. C

    WTB-Tecumseh HS40 Spark Wire Clip

    Need clip(s) for spark plug high-tension lead. 1970 HS40
  15. C

    HS40 Fuel Line Routing

    Another novice question for those with on-engine vertical seam tanks. Engine originally had horizontal-seam, plastic tank with outlet nipple in the center/bottom of tank. No problem with fuel line radius out of the tank into the shroud. I now have reinforced rubber fuel line installed and...
  16. C

    HS-40 Breather Assembly Q

    I don't have any experience with small block Tecumsehs so need a little hand-holding here. Is the breather housing one piece or two? Just looking to replace the element and it appears pulling it out of the narrow slot is not correct. Also, the housing gasket looks to be sandwiched rather than...
  17. C

    WTB- Mesinger Seat

    Looking for Mesinger, in black, 13~18" in length.
  18. C

    WTB- Gilson Bushings

    Pair of 0.75" ID, oval OD bushings needed.
  19. C

    WTB: Tecumseh 4hp Vertical-Seam Tank

    Better original condition preferred,not looking for restored condition. Anything out there?
  20. C

    Tecumseh 33288 (Taylor #100)

    NOS, boxed. $35 shipped (CONUS only)
Top