Search results

I am looking for the square ribbed covers that are for most Tote Gotes. OldMiniBikes warehouse used to sell them but they have been out of stock for a while now. If anyone has a source I would be interested. Thank you

Selling my late 1970's King O' Lawn JC Agajanian mini bike. Overall in pretty good shape, the standard light rust on chrome and seat tears, but it's all there including the original 5hp Briggs engine...save for the cool front decal unfortunately. It's in running condition but I must say that...

Thought this bike was very interesting and of historic significance. It's been on eBay for over a month now, it isn't mine, but it is a very rare prototype 2x2 Tote Gote! Very similar to a Rokon. I had heard tales of the 2x2 Tote Gote being developed for the military by Bonham, but not being...

The clutch cover on my clutch is loose, and I'm wondering what can be done to fix the problem. It's a Bonham climbaway clutch on a Tote Gote 670, the cover sits between the engine and the actual clutch. The cover has a spot for the key stamped into it, and is also supposed to have a smaller tab...

I was changing out the belt on my Tote Gote Nova. The torque convertor driver clutch kept pushing up against the motor so tight that it wouldn't turn over whenever I tightened the bolt down on the end of the shaft that holds the clutch to it. At first I thought my motor had seized somehow! A...

Am I correct? A larger micron fuel filter allows for more fuel flow but less filtration. (bigger pores in filter) A smaller micron fuel filter allows for less flow but more filtration. (smaller pores in filter) Briggs recommends their red color 150 micron fuel filter for engines without...

Okay this is a long shot but here goes...Years ago I was given a 1973ish CT70 by a family friend. He was a pilot and the frame of this ct70 had been modified so that it could fold in half by removing a bolt at the top of the frame and unplugging a connector in the wiring harness. This made it...

What was the max RPM Tote Gote's with the Climbaway clutch ran from the factory? I have two Tote Gote Nova's. One is a 670 I put a 7hp Tecumseh engine on, the other is a unmolested, well-preserved, 675 with the stock 6hp Briggs aluminum engine. Both run the same 1" shaft Climbaway clutch made by...

WANTED: Handlebar grips Brake Levers Foot Pegs (sans the covers, I can get those a lot of places) Rear fender (for Nova 670) Any condition. Name your price. Need to finish my restoration. Please send me a Private message or quote my post here so I am notified you have these parts...

Looking for a forestry service approved muffler with a spark arrestor like a Taylor muffler or a Nelson muffler. Just needs the "US forestry service approval" stamp on it. 3/4 inch threads needed, no smaller or bigger. Thank you, reply or send me a PM.

Looking for a dipstick and oil fill pipe for a 4-7 hp Tecusmeh flathead like the one pictured. Need for my build. PM me if you have one please.

I bought this shroud off eBay and the bottom ended up having rust holes in the bottom when I started sanding it. Didnt want to use it on my resto because of it. Other than the few small holes its solid. Extra ventilation. It came from Michigan. :hammer: It is free to anyone willing to pay...

This isn't my bike, but these are rare so I had to share it. Here is a rare 1962 mustang trail machine with it's original 5 & 3/4 hp Briggs engine with the oil bath air cleaner- Look at that motor! It seems to have a (likely multi-speed) gearbox that has some sort of kickstart mechanism on it...

I need to replace the points and condenser on my HH70 Tecumseh due to a no-spark situation. The manual says I can set the points "by rotating the crankshaft until the point arm is resting on the high side of the ignition cam." My problem is I can't really tell where the highest point in the...

Wanted: Rear fender for Tote Gote Nova model 670. A 680/780 rear fender might work too. PM if you have one and tell me your price. Thank you

I bought a new recoil assy for my 7hp Tec and there is a knot holding out about 2 feet of rope or so. :doah: Why? How come? What happens if I untie it? :confused: This is it and what it looks like:

I am restoring a Tote Gote 670 Nova. I need to run a pulse line to power the new pump, and I am wondering the best place to do so on this particular engine. I'm guessing I will need a fuel pump as these bikes came stock with a oldschool mechanical Tecumseh one that ran off the cam, as the...

Hi, For my Cast iron HH70 build I had to purchase a new air cleaner assembly, I decided to go with a kit I found on Ebay shown in the picture below. It has a cast iron elbow and paper element that some of the cast iron industrial "X/L series" Tecumsehs' came with. This means that the crankcase...

Looking for a clean/usable blower housing for a Tecumseh HH70 engine, NO electric starter bump. Looking for one WITHOUT fuel line/primer bulb holes in it (like a snowblower model). I just need a regular HH70's blower housing for this engine. I don't necessarily need the recoil portion of the...

Hello OldMiniBikes members, I am looking for 2 sets of the LORD Rubber sandwich mounts used on the 670 and 675 Tote Gote Novas. I own a 670 (under restoration) and a 675 (operable) both need a set of new mounts because the old are worn-out and ancient. I know several have replaced their mounts...