3/4

Hi all, Did Briggs make a 3.5 or 4 hp engine with a 3/4 by three inch crankshaft for use on a Rupp minibike? Thanks, Bill T.

NOS Comet 4" drum with 3/4 center, 45.00 shipped for the pair to the USA. Pay Pal or postal money order.

I bought this new on ebay search 12hp universal joint it cost $37.35 $14.34 shipping for a total of $51.69 I never used it I just slightly removed the sharp inside edges to make it less likely to bind then I greased it It's yours for $35.00 free shipping in the contental usa

It's time to let go of this fully restored Magnesium Go Power. I want $90 + ins/ship from (32952). This complete wheel was disassembled, blasted, and painted with a color matched single stage urethane. New races, fasteners and ready for show. Be advised. I may not be available to ship until...

I'm looking for a TC88 3/4" driver. If you have one for sale, pm me. Thanks, Tim

Wrong front forks, but they are suspended. Looks like OG TAV driven. Wheels in great shape. Big block. VINTAGE MINI BIKE Montgomery Ward Gilson mini bike | eBay No....I have other plans.:laugh:

Brand new, never used, 12t. $65 shipped.

I need a 420cc crank turned down to 3/4" so I can have a better option for clutches. And what price and how long ?

2 wheel stars, one rear tire and one sebac shock 11 3/4" center of eye to center of eye(was on an Eliminator)everything pictured except my knee $50. Shipping is on the buyer. Pms work best. Thanks!

I recently got a clean, low hours HS50 67061A (1975 I believe). Can the original 1" crankshaft be replaced with a 3/4" crank? I've seen a thread that discussed machining the 1" crankshaft down, but if replacement is possible with no resulting engine damage, that would be my preference. I may...

For a couple more days. Just sayin... :smile:

Looking for a plain bearing crank (3/4 inch) to fit in my 1991 model130212 5hp that currently has a 1 inch chipper crank. Anyone have a good used one for sale? This will be a stock governed engine. Thanks!

Have a little mini chopper finally found out that the rear sprocket and the original drive sprocket are T8F?? Either need another rear sprocket or a jackshaft to convert I know there are some people out there that have the little 49cc mini bikes and I know that some of them have modified...

Looking for a Tecumseh H70 3/4 crankshaft. I would be interested in a H70 short block too. Let me know what you have. Thanks

HEY So i have a monster moto 80cc and i bought a predator 212 engine and im ready for a swap! I am totally new and dont know **** I seen many swap videos and clutch videos but nobody explains how to remove a key. Only problem is the engine has a key thing preventing me from placing the...

Looking for NOS Comet Series 30 1" bore driver for engine PTO shaft that uses the asymmetric drive belt and the matching Comet Series 30 3/4" bore 6" driven variable pitch pulley unit. Must be made 10+ years ago by the original Comet Industries. I realize the newly taken over Comet...

Hey guys, does anybody have a used working 3/4" clutch they can part with for cheap? Also, I know this one is more random, but anyone have a crankshaft from a Honda GC160 motor long enough for a clutch? Just shoot me a PM, thanks!

I need a TC-88 complete driver in pretty good shape. Any help would be appreciated. Doc

Hello All, these fine mufflers fit the Briggs engines with a 3/4 NPT exhaust port, typically the 5HP engines. These will not work with 3-3.5HP engines. Only 3 for sale, gotta keep one for me! $13.00 to your door, lower 48 only

I only need approx 1 1/2" of the very end of the shaft.