i am building a mini that i bought from a friend that just sat underneath his porch. it had a lot of surface rust, so im getting it sand blasted. i bought most of the parts i need and just have a few more thing. i plan on putting one of my full race built clone motors from my go kart racing...
Want to start a build. Looking for a honda gx200 212cc or 196cc clone crank case and crank shaft.
I have tons of parts to trade or more than willing to buy for right price.
Thanks.
Is there any difference in a 5.5hp crankcase and a 6.5hp crankcase. I am very new to tearing down a motor and rebuilding it. I have several 5.5hp clone crankcase lying around and was wondering if I can put a 6.5hp crankshaft in one. Any help would be greatly appreciated.
Been looking around and a lot of questions involving camshaft installation so why not make a thread
Step 1
Remove your engine and set it in a clear area
Step 2
Remove spark plug
Step 3
Remove engine oil drain plug
Step 4
Remove the fan shroud and starter
Step 5
Remove your valve cover...
Can anyone recommend a decent big clone for me? Must run lights and charge battery. Saw some 16hp clones out there, but if they do have a charging system, it's measly. Doesn't have to be 16 hp, but must be 1" shaft. Help!
hey guys and gals,
after a long layoff due to a foot injury, I rolled the 'ol Baja out of the garage and tried to start her up.... to no avail ! She's got the 6.5 china clone Greyhound engine in her. She's been sitting up for the better part of a year, yep she had Sta-bil in the gas tank and it...
I have an assortment of Honda GX200 clone parts from Baja Warrrior Minibikes.
Clutch w/jackshaft assembly and cover $50 each
Crankshaft $20 each
Cylinder heads w/valves only $15 each
Cylinder head fully assembled $20
Fly Wheels $10 each
Exhaust $10 each
gx200 carburetors $15 each...
about a month ago I bought a stage 2 open modified lifan engine from Nr Racing. 14 cc head billet flywheel, 22 lb springs, bored gx200 carb, cl1 cam, Right off the bat i wasnt happy with NR racing because the intake side didnt even come with lash caps when promsied a stage 2 would. she started...
So im in the middle of saving up some money to build a clone to put into my bonanza mx project bike. My question is how long will these clone motors last with some mods? I'm thinking a cam billet rod and flywheel smaller head 22mm mikuni etc.... Im hoping this can be a great reliable motor for...
Just wanted to post a project I am just about done with.
This was originally an Eton Viper with a 70cc engine(or was it 90?).
Album Link
Things I did:
-Remove old 2stroke engine, wiring crap
-Added your garden variety Harbor Freight 212cc predator engine
-Hilliard Extreme heavy duty clutch...
My engine keeps sliding to the rear of the chassis under full power and my primary chain becomes loose I have installed grade 8 bolts washers nylock nuts
I'm thinking of installing a plate at the rear with two screws to adjust the motor forward
Any and all ideas welcome
Thanks
Kurt
Sent...
i put a predator clone in my doodlebug mini bike. i got it all installed and everything hooked up. i started it up just fine. but when i switched it from start to run. it took off away from me and was stopped by a wall. no damage to the engine or bike. i just need to know why it took off like...
My baja warriors gx200 engine vlew up and I was just wonderng if swapping for the ohv would be easy and I wouldnt need any other parts?
This is the new one I was thinking about..
196cc BSP Dupor Honda Clone Racing Motor Billet Flywheel Upgrade Cam Ruxing Carb | eBay
This is the old one...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.