fine

I have more of the later rivet on style that was correct 1971-1974 on the small frame H25-35 and HS40 and HS50 and could use the older style version like Joe51 repro's 1968-1970 and would like to trade. Original or repro is fine (would prefer Joes if its repro and NOT the ones currently on...

Hello, I am Gampy and I am new to this great forum. I have never owned a mini bike before. I always like to keep a project or two going. I think this might be one and also just might end in something that some of my grandchildren will enjoy. I live on a tree farm in central Mississippi and have...

https://www.youtube.com/watch?v=TzwjnN5XW3o JUST FOR FUN CLASS!!!!! Put me IN IF NOT THATS COOL TOO IDC!!!!

https://youtu.be/s8jki2rdJMo Hi everyone, I had my plug out, finding tdc and I noticed a clunk clink noise when turned over by hand. It happens throughout all different stages of the piston stroke. The engine runs fine and no loss of power. The engine has been built by one of the members on...

this is Pak Jak serial # 178, the bike was raised about 7" by who knows. The story is that PG&E used the bike to check on remote power lines but not sure. We are getting close to installing the motor, original 3hp Briggs, was surprised on how many original parts we could get. I redid the...

Would you just stick the bottom one back in the carb or would u change it anyway. In comparing it with the replacement i dont see much of a difference at all. I dont see an edge or squaring off at the tip the way the manual shows whens its bad. I just feel the original parts are better than...

I was wanting to know if anyone runs without the lower shroud, and if it would run hot or if it would be fine? Thanks

I was breaking my new motor in with the bike up on a stand and everything was going fine ..... all of a sudden it bogs and dies. I see fuel dumping out of the air filter so i turn it off and cleaned up the spilt gas. Then i started it again without turning the fuel back on. Ran fine until the...

I took out the gov. the cam came out when I took of the side cover. I am sure that I lined up the dots on the cam. So I installed a throttle plate and put the motor back in. Stars fine, runs fine on choke but dies when you turn of choke. Sounds like high speed lean out ? took out carb. cleaned...

Well guys I know it's hard to believe but as of today I'm the proud new owner of the fine custom DB , It appears to be previously owned by Cheezy as you can see , I however was unable to work the clown suit into the deal .This fine example of modern engineering will be parted out completely as...

cat kick stand slightly loose when open but works and locks up fine $30 shipped :thumbsup:

After picking up the minibike from the autozone my son started the bike up noticing that the engine is a lot more quiet. When he rode it it almost flipped him off because of the torque which took some getting used to haha. The next day he rode it to his friends house and came back and was...

good used 14cc head . just needs a good cleaning . complete stock head $50.00 shipped i will throw in stock flat top piston (has 3 dings on the face but should be fine ) lifters,stock rod,push rods,stock cam if you want those aswell:thumbsup:

Just picked up an old Ariens snow blower, 1973 I believe, with a Snow King on it that is backfiring through the carb. Starts up cold and runs fine until under load. I assumed it is the carb throttle shaft and dug up another used carb and installed it, same thing - runs fine until I hit the snow...

My new bonanza fine today December 22

Today I fired my minbike up and took a ride maybe five minutes up the road and on the way back two cops pulled me over and followed me back to my house and they nearly gave me a fine but I talked them out of it. I told them I had just made the bike and was testing the chain and they ended up...

I have a 1970 2 HP Briggs and Stratton. It ran fine. I took it out of my MX Duster and cleaned it pulled the recoil cover off and put in a new rope. Cleaned carb, painted, changed oil and new plug and oil. Reassemebled and now it wont start. In fact I'm not getting spark? I have tried...

First I have ever seen this The scariest path in the world?

When it comes down to using an 5/8 axle bolt ... What do you advise using?? ... An 18 thread or do you compromise by using an 11 thread ?? ... When it comes down to availability the 18 thread is tough to find over 8" in a finished bolt ... Any thoughts ???

Can someone point me in the right direction to find some posts about getting the most out of a hs50? tricks,removing governor,problem areas with these small blocks,best plug to use,carb tricks,timing, ect. thanks 6gun