flywheel

Swapped the stock (ct200u) flywheel to “69730 69736 Aluminum” some cheap option on Amazon. Kept the original timing key since it matches what came with the new wheel. Now I can crank all day maybe get a slight sputter but won’t run. I swapped back to the stock and now I can’t get it to start at...

Does anyone know if there are any flywheels with similar tapers and sizes as the 5hp Flathead, don’t wanna pay $200 for a flywheel that will barely get used but also don’t want to risk a cast flywheel, will any sort of clone flywheel or something like a predator or Lo206 flywheel, timing doesn’t...

Is it possible to use a V60 blower housing and flywheel on an H60? both are early (around 1969-1970 engines) Thanks!

What's the difference between these flywheels, and which is better? I've only ever use ARC flywheels, but have been wondering about this one.

I have Less than 30 miles on it. I will trade for a nice straight billet flywheel for a Hemi or Sell this for $100 shipped save ya $30 some bucks...... also I have a motorized bicycle so I don't post a lot here. But I get all my technical info here! Ultra-Light SFI Certified Billet Aluminum...

I have Less than 30 miles on it. I will trade for a nice straight billet flywheel for a Hemi or Sell this for $100 shipped save ya $30 some bucks...... also I have a motorized bicycle so I don't post a lot here. But I get all my technical info here! Ultra-Light SFI Certified Billet Aluminum...

My pull start is out of commission and while waiting on the new assembly to arrive, I tried starting the engine using a cordless drill and 11/16 socket. The engine started up, but the nut on the impeller loosened up and caused the impeller to fall off while the engine was running. I tried...

I'm working on a Briggs Animal engine. It has a PVL flywheel on it. It requires a simple puller like this one from Amazon. The problem is if I ordered it today it wouldn't arrive till Tuesday according to their web site. I would like to make one tomorrow and not wait 5 days for one. Does anyone...

Have a H50 that I need to pull the flywheel on to check out the kill switch wire, bike was running fine last summer then died and wouldn't start. Cast Iron Flywheel has no tapped holes for pulling. Any ideas?

1- ARC 6377 stroker rod in box. Looks like it is slightly used $52 shipped 2-ARC 6370 stroker rods. Used. $45 shipped each 1- ARC 6213 stroker special rod. Used. $65 shipped ARC flywheel. Used. Looks like aluminum was welded in for weight or balance. $55 shipped 4 spring 2 disc smc clutch...

Ambush racing billet flywheel used once like new and an ambush adjustable timing bracket new with coil $80 each shipped or $150 for both to same location .. can text 845-505-2198 for pics or I will post some in a little while

I have an Aspera HT35 from the 1960's/1970's which for all intents and purposes is the same as an H35. I recently got an H35 lighting coil from an OldMiniBikes member and the flywheel rubs against the coil. Question is: are the flywheels on the lighted H35 engines different than the flywheels on the...

Hi. New to the board. Does anyone make a 5HP Briggs (Flathead) billet flywheel that can be used with a pull-start? I want to do some mods to improve performance, but I believe all the billet flywheels are set up to be started with a portable starter. Looking forward to comments. T

Hello everyone Ive got alot of projects but what Im currently working on is an Arctic Cat Whisker I picked up in Duluth Mn. Its a nice survivor but it has low spark not even enough to get through the spark plug. Further inspection revealed a wire coming off the coil is pretty corroded. Ive...

Looking to trade a predator billet flywheel for the same flywheel for a gx200. Thanks

Arc gx200/clone flywheel excellent condition $65 shipped

Predator non hemi ultra lite billet flywheel like new condition $75 shipped part#6602p

Looking to see inf anyone has a late model big taper/electronic ignition "lighted" flywheel available. Part number is 611087 fits the H50 60 and 70, or the conversion parts to make the lighted assembly. I sent a PM to Tmack but have not heard back if he has any of the parts or still does the...