hs50

As many of you may know... I tend to build polished turds from crushed junk.. I've determined that most lighting coils are all about the same basic coil pack.. With whatever different options... http://www.oldminibikes.com/forum/tecumseh-engines/58774-tecumseh-6-horse-lighted-system.html I...

As many of you may know... I tend to build polished turds from crushed junk.. I've determined that most lighting coils are all about the same basic coil pack.. With whatever different options... http://www.oldminibikes.com/forum/tecumseh-engines/58774-tecumseh-6-horse-lighted-system.html I...

Looking for carb for an old HS50 tec engine from a VT-5 Heald, Hello Bill! The motor is a hs50-67145c and the service carb is a 631796A. There appears to be no aftermarket equivalent, however this carb seems to be a catchall for a lot of older HS50 motors. My carb is frozen up and it just...

Up for sale.... All parts are off a NOS "HS50" from the late 70's to the early 80's. I've been trying to find out the model year, but have had no luck. So you will have to make the sure if these items that I have up for sale will work for your application. I will do all I can to help out...

I bought this HS50 from a guy..... That told me it was NOS and never had gas /oil in it. I do believe him because I'm taring it apart and there are NO SIGNS of it ever being ran. There's also NO SIGNS of any numbers to tell what year it is :mad2: The owner had ground off the numbers on the...

I have a good running tecumseh hs50 for sale. Has new points and condensor. Clean and in great shape. It needs a carb rebuild but still runs good, carb seals are leaking. Asking $100 obo plus shipping. Its located in dearborn michigan, cash and paypal only.

tecumseh HS50 std ring set # 33567

Can anyone make me a intake to run a mikuni on my hs50?

Does anyone make a intake manifold for a hs50 to run a mikuni carb on it?

Decided to part the engine out. HS50 parts: Block has excellent compression with Cylinder head with bolts -$70 HS50 Front Guard has crack on top by the bolt-15 Flywheel ant started cup-$45 Recoil-20 Point set up It has new condessor, coil, points, set up and ready-40 5hp...

delete, sorry

Hi, i picked up an H50 and a lighting coil for my 68 Rupp. Serial number starts with a 1. Im going to rebuild it. Im down to removing the valves. I want a good strong running engine. My friend has a machine shop, "if he has time" he will do the machine work. Im going to need a new carb and...

sorry posted twice

I am in need of a good tecumseh hs50 adjustable carb. If you have one pm me. Thanks.

Today when I brought my minibike outside to start it, I noticed my clutch was rattling as I pushed it, so I oiled it,and the noise went away. When I pull started it I noticed a loud rattling noise for a few seconds before the engine stopped. Now I cannot pull start it. I pulled the shroud...

Have a tecumseh HS50 and was wondering: 1-Will the piston and rod come out the bottom of cyl? ( and no, when off, not at high RPM :wink:) 2-Anybody reuse a head gasket? 3-Is the wrist pin pressed into the rod?

i am trying to find a nos h small frame or hs50 tecumseh for a new ruttman project i am about to start.would consider one with very low run time also. ls195 snow king engine ok to if it has 3/4 crankshaft. please no junk or fool me's please. must be able to ship to md 20601...

Tecumseh HS50 67344H (B) DOM 42240. Engine runs well, like new IMO. Has nice adjustable carb that everyone wants. Got this one off Sears chipper/ shredder. Chipper/ shredder was fairly worthless, hence engine was used very little. I tried the chipper/ shredder one time before taking...

Tecumseh HS50 for sale: Tec HS50 off Sears chipper/ shredder, 7/8" taper shaft

Tecumseh HS50 for sale: Tec HS50 off Sears chipper/ shredder, 7/8" taper shaft