key

Hello Everyone, I made a post here last week about my briggs and stratton 3hp.I replaced the breaker points ignition to the electronic system. It had a flywheel key that was sheared in half, and thus I was unable to start it. I have replaced the key, and torqued the engine to the proper specs. I...

Hi guys , I got a doodle bug with a preiditor motor. I like to add a key on and off . Can someone link me to the parts I need please. Also like to add a front light and rear tail light,what parts needed for that thx Thx Tom

One very important part of my project has a 1 3/8 shaft normally a shaft of this size would use a 1/4 keyway but mine has a 3/16 and the sprocket that goes on this shaft uses a 1/4 " key. step key to the rescue. I am glad these exist otherwise I would have to make one somehow

The fix/built in key on my new to me comet clutch is almost gone. The prior owner had drill a small hole on the engine shaft so to get the only set screw to sort of lock the clutch to the shaft. I am contemplating drilling a couple holes right above the shaft key way and install two more set...

Does this jackshaft look familiar to anyone? Came in a very random mini bike parts lot that gave no clues as to what it was for (looks unused). Kinda short overall, it is drilled and tapped on the short side.

First off, i'm not sure if this is in the right section (mods please move if so) but I ordered a keyed ignition with an on and off to mount on the blower housing then run the cable strait down and out the bottom and along the outside of the bottom of the engine to the old kill switch area. I...

What size woodruff key is needed for the axle? My buddy just called me looking for some to put the drums on his Dunecycle axle...All I have is 5/32" x 3/4"... I don't know why I even have them. I've never used them.lol

Hey guys im trying to expand my knowledge on these predator motors. Ive seen items for sale like timing keys. What are there and how do you install them and what performance gain do you get?

Hey everybody, First 56yr old newbie question regarding flywheel key problem that I cannot figure out:anon.sml: I had a spark problem on my H30 that required me to pull the flywheel to investigate. I traced it to a cut condenser wire that I fixed, but when I put everything back together, I...

I know everybody swapped their engines out so let's we what happens... I need the timing key for the 97cc engine they came on the Baja racer doodle bug... Please let me know asap thank you

I have a Tec H60 with points ignition and would like to know what key to order for the flywheel? Also what oil fill tube to get mine doesn't have threads?

When installing a new timing key do you want to try and advance the flywheel over as much as possible or is the idea that this will move itself back and forth when spinning up and down ? And to quadruple check its 54lbs. for stock flywheel on a clone engine ..correct ?

So i have a mini bike with a 6.5 HP engine. And the clutch is missing the set screws.. Where can i find extras? Also from what iknow they also are supoosed to have a keyway key but idont have one. What can i do? Ene links as to where i can order some? Thanks

Picked up this new carb to good to pass up Can anyone tell me a little about it.a few guys in my area are running them with good results .I've been running a 22mm roundslide mikuni knockoff on my predator 212 runs good mods are Arc rod &flywheel 8°advaced key Black mamba sir 18cchead 27/25...

I picked this up a while back but just got around to looking at it. I was going to flip it , but its kinda growing on me. 1965 if I read the serial # right. has compression but no spark and the point cover was off when I got it. Im the 2nd owner, has dealer key chain and original key...

I just feel like the driver isn't grabbing enough shaft. After all the spacers are put on, the driver is really only grabbing like maybe 3/8" of the key way. It just seems like that is way too little. Anyone have any insight?

3 4" to 1" inch w Step Key Gas Engine Pulley Crank Shaft Sleeve Adapter Predator | eBay Has anyone used one of these? I want to run a 40 series on a 3/4" shaft. The question is the key. I know it has the key to go onto the 3/4 shaft and into the adaptor 1/4 slot. It is hard to tell from the...

What are the 2 wires yellow and black hook to on the ignition. I don't have the right key swith. I bought one at Napa it has. m / s / b these are marked on the key switch. Thanks it's a 72 fos sundowner thanks for you help. Working on it right now.

A couple quick questions regarding my Tecumseh H60 1. Any tips on getting a stuck flywheel key out. I used penetrating oil, hammer, attempted to pry it up somehow with no luck. Any suggestions. 2. I currently have the side cover removed and find it nearly impossible to turn the engine...

$5 shipped. Just drop in a envelope! good luck, happy bidding!!!!! New, never used! SOLD SOLD SSOLD!!! Thanks Hal Armour!