keyed

I bought this new on ebay search 12hp universal joint it cost $37.35 $14.34 shipping for a total of $51.69 I never used it I just slightly removed the sharp inside edges to make it less likely to bind then I greased it It's yours for $35.00 free shipping in the contental usa

I only need approx 1 1/2" of the very end of the shaft.

Need longer shaft on the 212cc, The splined hub driver only fits on 3/8" of the end of shaft.

I just picked up 8 new old stock engines that have been sitting in their boxes in a barn for the last 30 years. NOS brand new complete with gasket kits 2 are 3/4 keyed shaft 3 are 5/8 keyed shaft 3 are not keyed have taper or funky threads good for putting your crank in. Priced at $125...

Hi everyone, This will be the build log for my 2x2 project. I love tinkering and have completed a few big projects in the past including a 4x4 buggy, but this will be my first 2 wheeled project. In fact I have only ridden a mini bike once and crashed almost immediately...... but I'll figure...

I posted this in the general section earlier, but maybe it belongs here. I am working on a go kart , but it only has part of the drive clutch. As you can see it is missing the stationary plate. I really dont understand Comets numerical series , at any rate I am in need of the stationary plate, ...

Go I got a free 10 hp motor from my boss but it's not keyed and the shaft comes to a point I think it is off a generator . What would be the easiest way to get a clutch on there ?

Like the title says. Brand new. $25 plus 5.95 priority shipping.

I've been looking, a little help would be great. Need 5/8" keyed shaft 42" - 48" long Need them to ship International & take Pay-Pal. Any Ideas?? Thanks

This is a 5/8" keyed and threaded shaft 10.5" long. Its a BMI item and retails for $26.95 5/8" Jackshaft with Washer (02014), www.bmikarts.com : BMI Karts & Supplies : Go Karts Parts : Racing Go Kart Parts : GoKarts : Versailles, Ohio : USA : Indoor Track : Tips $25.00 OBO shipped anywhere...

Hey I have a Tecumseh H50 engine that came on a minibike I traded for recently and it seems to be unkeyed or the keyed part of the engine could have been cut off:confused: (the end of the shaft is rough like its not factory made)? Does anyone have ideas of how I can attach a clutch to this or is...

Tecumseh engine, model #

Tecumseh engine with its shaft un-keyed

Tecumseh engine with its shaft un-keyed

Tecumseh engine with its shaft un-keyed

I know they're rare, but I'm fixin' my Dart Kart to be a goer not a shower and as I have a good set of Manco wheels to use for the front I'd like to run 'em on the the back as well. Got to be cheaper than Rupp turbines.... i've seen 'em here once in awhile, anyone got a pair?

Does anyone make 1 inch live axle bearings with a 1/4 inch keyway cut into the race? I would like to key the bearing to the shaft, just because:shrug:

I recently rebuilt this engine and have already sold the carb & tank setup. It came off of a Craftsman Rototiller rental and was said to have starting issues. When I took it apart it was easy to see that it was well maintained with frequent oil changes. Clogged pickup tube seem to be the...

Has anyone got a 1" live axle, 10" or more long, with a 1/4" keyway? I am in UK.

What sites sell 1 solid live axle with a 1/4inch keyway running it's length? I need some for an axle but google seems to not bring up anything.