manifold

  1. JohnnyTillotson

    Intake manifold hole size

    What's the theory behind these skinny flat intake manifolds that hold the carburetor a bit lower than the regular one? I never noticed how much smaller the hole Liz when you hold it up to the back of the engines intake. Is a small hole causing more suction and thus the gas flowing inside faster...
  2. L

    24mm flat slide + manifold wanted

    Looking for a 24mm flat slide with manifold.. mikuni, pwk, oko, etc thanks
  3. Sprocket86

    HS50 slant intake manifold.

    Getting closer to finishing my 1971 MTD build and I'm in need of a Tecumseh HS50 slant intake manifold. If anyone has one that they would part with, shoot me a PM with a price please. Thanks.
  4. C

    Mikuni manifold DIY facing rear

    I need to change direction of carburetor for fit. Has anyone used this method to redirect carburetor towards rear? Any performance issues using small section of hoe? Using radiator hose in-between cut manifold AGK - DIY Curved Manifold - Affordable Go Karts thanks
  5. David wulf

    Polished aluminum intake manifold

    I have a aluminum intake that will mount a mikuni 22 to a Briggs 5 hp . It has been polished by me . Price is 45 shipped OBO
  6. K

    WB 820 manifold

    Hi.. Does anyone have a GEM 12v intake manifold or similar manifold to run a tilly HR single carb on a WB 820. Even just the base and reed block will do .... Thanks
  7. David wulf

    Intake manifold for sale , tech carb to Briggs 5hp

    For sale is a intake manifold to put a tech carb on a Briggs 5hp motor . And to help sway buyers is a custom throttle setup to make this combo work . You only need a carb and cable Clevis , not getting mine . Price 35.00 shipped
  8. David wulf

    Mikuni 22 to Briggs intake manifold

    For sale is a steel intake manifold for a mikuni 22 to a Briggs 5 hp . Price 30.00 shipped
  9. David wulf

    Intake manifold , mikuni 22 to Briggs 5 hp

    For sale is a steel intake manifold to bolt a mikuni 22 to a Briggs 5 hp . It's about 2 1/2 inches long and angles out to the pull start side slightly, to get it away from the exhaust. Price is 30.00 dollars shipped
  10. F

    Wanted: Manifold for a 22mm Mikuni Carburetor

    I'm looking for a Manifold for a 22mm Mikuni carburetor. I'm located in California. Post pictures and Prices
  11. C

    Briggs manifold

    Want to connect an Animal PZ22 carburetor to my Briggs Raptor block. I need a manifold.
  12. paul kellam

    Please help I.D. intake manifold

    Hello all, I found a old tecumseh intake manifold in my parts bin it is stamped 51 0 124 any info would be appreciated
  13. 125ccCrazy

    wanted: gx390/420 billet rod, cam, intake manifold, flat top piston for a 420cc

    looking for a good used or new stock length rod, cam no bigger than 360 lift, intake manifold for Mikuni...
  14. manchester1

    Wanted H35 Rupp slant manifold

    Looking for the intake manifold for a Rupp H35. The slant that makes the carb level. :laugh: Thank you for any help.
  15. fistfullabar

    hs40 carb to engine manifold bolt size

    Lost mine need too buy some so i can find um. Anyone got the specs handy for thread and pitch manifold to engine bolts?
  16. J

    Intake manifold

    Dose anyone know what kind of c arburetors i can use with the Billet Intake Manifold - Tillotson to Honda/Clone from OldMiniBikes warehouse. Or know the measurements ??
  17. motomonster212cc

    el Tigre seat. tecumseh 3.5 slant manifold, scrambler front racing plate.

    looking to buy an El Tigre (bird industries) seat, and a tecumseh 3.5hp slanted intake manifold and a rupp scrambler front "racing" plate. thanks and let me know, Lyle
  18. Taco Loco Joe

    In take manifold for HS 40

    Model HS 40 552908. Tecumseh. If you don't have one, which one do I purchase ? Thanks OldMiniBikes
  19. R

    Tillotsen carb, intake manifold, velocity stack

    Tillostesen HL368 carb, intake manifold and aluminum velocity stack. Carb is mostly dissembled but hardware and components are all bagged up. $40 shipped.
  20. 6

    wanted Arctic Cat Ramrod intake manifold

    Anyone have a 98cc Kawasaki ramrod intake for sale or trade for other arctic cat parts pm me if you can help Mark
Top