oil

I have a honda 6.5 Greyhound engine, needed to know what weight and brand works best for these engines

ive got a few questions as a beginner. im wanting to do a cosmetic restoration of this motor to use on my arco build. its a good running engine, it just needs a good cleaning and a coat of paint. i want it to look new again and just curious as to what paint to use and if theres anywhere to buy...

If I'm reading the label correctly, it would be from 2004. Complete and never had gas or oil ran through it. $100 plus shipping from Alabama (35023). Thanks

Two of my bikes have Briggs motors (Cat400X & Ruttman Toad) I keep them in our heated basement over our long winter and I've noticed after changing the oil that they both seem to be leaking a little oil, nothing major maybe a couple of tablespoons. One is a 1966 the other from the mid 70's. Is...

New hemi predator. Never started. Has been disassembled, clearances checked. Big end of rod opened up to .002+ oil clearance. Governor removed, low oil level sensor removed. Holes drilled and tapped and plugged. Has Arc top plate and throttle linkage, box stock pipe and rlv silencer. 10.8 valve...

does anyone have info on low oil sensor bypass ?

Custom Harley Oil tank, Great tank for your "Buildoff Project" . About 8lbs. Approx: 9 1/2 long, 4 1/2 wide Original black oil cap included, Bottom nipples I believe are 5/8 and nipples to top of gas cap height: 6 3/4 $40 shipped U.S. 48, $50 with additional machined cap, (needs "O" rings).

Hi guys, Picked up an old h80 Tecumseh . Cleaned the carb and got it running . Changed the oil and was careful not to overfill. It runs strong and idles perfectly but oil is dripping out the breather. It does not smoke at all. If the rings are worn would it not be pumping blue smoke out the...

pickd up a used 6.5 clone this week. Has no spark. Disconnected switch and low oil sensor. It has oil in it. Still no spark. I took the coil off. Is there a way to test the coil? Thanks.

This seems like it would be a common issue. But my drain plug dumps out onto the motor mount plate. What are people doing to keep oil changes cleaner? Advice and pic welcome. Honda gx140 on a manco streaker.

Custom Harley Oil Tank I was gonna use for a Mini Bike gas tank. $45 shipped U.S. 48. Weighs about 10 Lbs. L=9 1/2 W=4 1/2 Comes with BLACK heavy screw in cap, shown. 3 outlets on the bottom, rust free since it only had oil in it. Light Hi-Temp Black Krinkle paint, If you want another coat...

Brand new - Never started - Never put gas in - $75.00 OBO + shipping

Hello all, I have purchased a benelli dynamo mini trail , I was looking for infomation on oil mix engine identification 50 or 65 cc, trans oil what year etc,. I already borrowed the wiring diagram which is identical to mine. the engine was stuck but looks to be able to be cleaned up...

Hey everyone, I was wondering what type of oil should I use for my Baja Warrior 196cc. If anyone knows a good brand of oil to use, please reply. Thanks.

Soaking the chain in oil to help remove dirt and other debris.

Where can I get an oil seal for an HS50 with a ball bearing side cover? Engine # is: HS50-67124D. Most of the illustrated parts lists I have found don't show it.

So I just rebuilt my briggs and it smokes since oil gets into the top end. And when I say oil, I mean a lot of oil. My rings are good and properly spaced, also, the cylinder is good, valves lapped, guides good. The only thing I can think of is that I milled the head too far down, I think I went...

Does any one out there have a diagram or video of how the cam-driven oil pump works on a Tecumseh? Question#2-Does an internal oil pump enable the engine to operate at different angles? Thanks for any replies.

oil switch ess unit