power

So I just got a free, running go cart has a briggs 5horse fun power engine? Guessing that's what's called a flathead? Anyways where can I get a few performance parts for it? What parts out there are interchangeable seeing this is a probably 10 year old motor. I just wanna get a little more power...

So even though this engine isn't and will probably never be on a minibike I still though you guys were the right people to ask. So recently got a used snowblower. With a 4HP Tec engine. The serial says HSSK 40. So far I have cleaned carb, replaced fuel lines, new fuel shutoff valve, attempted to...

I have a little OHV 5HP Power Sport engine with the governor still attached. I was thinking of removing it. Does anyone make a billet flywheel for these motors, or know where or which model I would need? Thanks!

Been wanting one of these for a while now, Its a little dirty and I haven't heard It run yet....but that's OK it does turn over and has good compression. My good friend and brother by another mother Eric (CarPlay) is sending me a gasket set so that I can clean it up and check It out. No suped...

I was looking at different ignition coils on Ebay and was wondering if it matters which one I buy for a newer fun power engine Genuine Briggs Stratton 397358 Armature Magneto 5HP Ignition Coil | eBay Briggs Stratton Replacement Engine Ignition Coil 802574 Fits Quantums 5 6 75HP | eBay...

I'm looking for a 6" Go Power rear wheel to replace one that is cracked. Thanks

My local Craigs List has an ad for 2 nice condition 6" Go Power Wheels with bearings, sprocket ( no brake ) tires and tubes. The asking price is $425. Is the seller asking too much for the pair? Thanks

My local Craigs List has an ad for 2 nice condition 6" Go Power Wheels with bearings, sproket ( no brake ) tires and tubes. The asking price is $425. Is the seller asking too much for the pair? Thanks

Hi everyone, I just got a new Baja MB200. It's fun for what it is but I am already thinking of mods. To me the first and most important mod would be a better brake. I read a thread here on OldMiniBikes where a guy added a front brake... that could be in the cards at some point in the future. But I...

Really nice set of 6" go power rims with tires and 60t sprocket. $200 shipped

I have a used Tec Power Sports 5HP engine for sale It will rum came off of a Manco Fat Cat It needs a cleaning $50 Plus Shipping from 89521 It has everything on it the way it came from Manco

I need a single half 6" Go Power wheel or will take a whole one if necessary. I'm trying to complete a resto bike and I'm down to this. Anyone have a half sitting around they don't need? Thanks, AJ

How do I get more low end power, or at least some better accleration? I could change my gear ratio but that's pretty difficult.

looking for a good rear sprocket for go power wheels, the one with three studs

This time a little model 500. $90. Never run. I think im gonna put this one on the minion cycle and use that Jacobsen for another bike. It was too heavy anyway. Real hard to balance. This is the 3rd one ive gotten from the retiring lawn mower repair guy. Cant find anything abt em online. But...

I have a h35 that seems to run out of pulling power once it reaches like 10-15mph. It feels like it just dies and then once speed comes down it has power again. Can't seem to keep it pulling. Any ideas? Thanks

For Sale is a early model POWER PRODUCTS 2 Cycle 2.5-4Hp Engine Model 3-16 Engine serial # 154981w75 Very Clean -All parts included Very Good compression Shaft is 9/16th's - keyed - 2.250 inches long Tillotson Carb Exhaust header Needs some TLC Local Pickup or Will ship Cant get pics to...

A few years ago I was going to build a Power Products engine for my Rupp Dart cycle I bought this NOS 9/16" clutch assembly from Power Products guru Hank Rotoff...or he told me where to buy it I forget which. I ended up building a Lauson 4 cycle for it. Anyway it is sometimes hard to find the...

Got this bike about a month ago. Frame was not very good. I decided to do some modifications. Fabbed the brake back to stock. I took about 3" out of the heigth of the frame. Made the frame fit the 1962 Tecumseh Power Products Super 58. The seat is temporary, having a new stock version made.

Hello, I've just finished this bike build. You can see the build thread here: (won't let me post the link to a popular engine kit forum.. username beginner01... weak....) Funny thing is, most times I search on google for an engine/driveline answer, I end up lurking here. :thumbsup...