pull

  1. S

    Govenor arm inside case noise

    Hello, the previous owner of my gx140 motor disconnected the governor linkage and the stud is only sticking about the case about 1/8". It sounds like it's hitting something inside. What would be the easiest fix for this? I was thinking of tacking a bolt on it to pull it up and drilling a cotter...
  2. vegascharlie

    mystery engine

    Was digging around in the back yard and found this old farm tool i was checkin out the gas tanks for use on my mini bike. Anyone know what kind of motor this is? It looks like the spark plug wire goes into a box next to carburetor. The pull start is old style with wrap the rope and pull. I dont...
  3. J

    wanted DB30 doodlebug 99cc sidepopper pull start recoil

    as the title states, i need a doodlebug 99cc flathead recoil pull start. cheap would be good, free would be better lol.
  4. gbones

    B&S pull cord cover

    I'm looking for a 2.5hp or 3hp pull cord cover. I'd prefer an older style that has the raised B&S letters on it. After a few ours of messing with my B&S and finally getting it running (2 trips to the hardware store) I had it running great. Then I wanted to hear it run one more time for the day...
  5. R

    6.5 HP Pull cord difficulty

    Hello everyone. I have a 6.5hp powerfist engine, and have a little difficulty starting the bike. It seems the pull cord gets stuck about half way of pulling it. Now, I can pull the cord past that spot easily, but it seems odd that there is a spot of resistance while pulling it. When I first got...
  6. jeep2003

    pull starter interchange?

    Will a 99cc clone pull start fit a gc160? its the same as the 79cc one and probrobly the same as the bigger clones but im not sure? Thanks :thumbsup:
  7. S

    Predator pull starter

    Havent seen a Predator up close yet but can the recoil starter be removed and rotated to put the pull rope in a different position? Thanks!!
  8. jdogg

    Aluminum pull start handle

    Made a handle for my engine on my project Trail Blazer. Started with a 1'' thick by 4'' x 4'' aluminum block (enough for two handles, but wanted extra incase I screwed up :laugh:) Used a hole saw, drill press, vise, drill bits, assorted files including a rasp, hacksaw, sandpaper...
  9. ozark caveman

    Need A Briggs 8hp Pull Cord Assembly

    Need the pull cord assembly for this engine. Please help!.
  10. ozark caveman

    Need A Briggs 8hp Pull Cord Assembly

    Need the pull cord assembly for this engine. Please help!.
  11. F

    Trouble pull starting DB30

    I changed the oil for the first time in my doodlebug 30 with the 97cc stock engine. It was running fine. I also put in a new upgraded clutch and torque convertor kit. Oil level has been triple checked and there is gas. The problem is that there is so much tension on the pull start rope and...
  12. jeep2003

    2 stroke pull starter

    Got this old pull starter with the cool art deco handle i dont know what its for. Looks like its designed to be either cw or ccw with a few different parts. Thanks
  13. E

    GC160 hard to pull

    Okay, so i bought a gc160 for $100 runs great and fits my db30 perfect but is hard to pull. I changed oil, plug and it pulls normal until it hits a certain point (obviously at the top of the compression stroke) and if you dont time it right and pull with this in the middle of your pull it will...
  14. P

    Lookin for help-hard to pull start

    So I have a Baja 200 that i installed a Black Mamba Jr cam, 26 lb springs, billet flywheel, cold air intake, header, and 8* timing key into. Now, WHEN I do get it running, it runs fine, but I have a serious time starting it. When I pull the starter it will jerk itself out of my hand seriously...
  15. Mac

    Rubber Pull Start Handles (5)

    Five unknown brand rubber starter rope handles. You should probably use a small washer on the rope in the handle to prevent the knot you make from pulling through. $1.00 Delivered anywhere in the lower 48 states. PayPal is good or whatever you wish to pay with, except Wooden Nickels.
  16. Dragbikemini

    New take off predator 212 pull start.

    New take off. 15$ plus shipping. Don't mind shipping quotes but just so you know what to expect it's 3lbs from 10509 Brewster, NY. Comes with cup and kill switch but no ducting on this one. Ducting is the shiny covers BTW Will be traveling for work so last day I have to ship on this is...
  17. roccosbike

    1968 Tecumseh 2.5hp pull cover

    View image in gallery View image in gallery $25 plus shipping
  18. Dan-E-boy

    Hotrod pull wagon build

    HI fellow OldMiniBikes'rs, this thread is for a custom radio flyer that I'm building. Here in socal there are a lot of car shows and car/motorcycle swapmeets to go to.. at least a couple every month.. one of the cool things to look at while hunting for treasures are the custom radio flyer wagons that...
  19. yalipito

    Pull starting high compression engine

    Hi guys, I have a briggs intek 206 with .060" shaved off and it is pretty hard to pull start. The cam does have the compression relief mechanism but I have not figured out the sweet spot when starting. Is there something that I'm missing? Or is it normal for it to be very hard (lift bike off...
  20. cyruss503

    tecumseh pull starter recoil..

    Hello all! im in need of a starter recoil for a tecumseh 6.0 powersport. would be grateful to anyone who wants to part with one!!!>>>??? thanks! fw
Top