rear

  1. G

    Rear wheel binding

    I have an old Trail Mate that I am bringing back to life. I put new bearings in the front and rear wheels. The front spins free but the back seems like it's being squeezed by the axle bolt. Do I need a spacer between the bearings or other piece of hardware? Any help is appreciated! Thanks.
  2. B

    Db30 rear wheel question

    Trying to put my db30 back together , It was apart when I got it. My question is the rear wheel has an offset hub, does the sprocket go on the shorter side? Thanks.
  3. Zooming993

    WTB Simplex Mark II Rear Sprocket Assembly

    I'm Looking for either a 60 or 72 tooth sprocket for a Simplex Mark II Go Kart. It would be great if the sprocket is in usable condition but I will also consider a sprocket with worn teeth, I can use the hub. Thanks
  4. Zooming993

    Need a Rear Sprocket for a Simplex Mark II Kart

    I'm Looking for either a 60 or 72 tooth sprocket for a Simplex Mark II Go Kart. It would be great if the sprocket is in usable condition but I will also consider a sprocket with worn teeth, I can use the hub. Thanks
  5. L

    MCP rear hydraulic brake on doodlebug

    Has anyone run a mcp rear hydraulic brake on a doodlebug or have any pictures of a person that has? I'm trying to run a mcp brake with the stock disc and re-weld a bracket, just wanted to brainstorm some ideas off other members on this forum that have done anything similar, thanks.
  6. T

    Wanted: straight DB30 rear rim and disk

    I may need two so let me know what you have and how much you want for each
  7. chopperbunch

    Clutch, rear sprocket alignment

    Do I need to move the engine to the right? I worked hard to center the rear wheel, which included placing a spacer in between the drum and back plate. So, I would rather not move the wheel out to the left. If I move the engine, should I order an engine plate before the re-location? or just cut...
  8. chrismh

    WTB Fox Sprite rear fender

    I am looking for a rear fender for a 1966 Fox Sprite. Also looking for a ID Tag for a Rupp Dart Cycle. Thanks!
  9. K

    14 inch tire diameter, 13 tooth clutch, 53 tooth rear sprocket. Okay to use?

    Right now I have installed on my motovox a 212cc predator with 14 inch tire diameter, 12 tooth clutch and 58 tooth rear sprocket. Will it be okay to switch the clutch to a 13 tooth and the rear sprocket to a 53 tooth without burning up the clutch?
  10. neo71665

    gilson/monkey wards rear sprocket

    Anybody have a good source for new 36 tooth rear sprocket with the 3 hole bolt pattern?
  11. CarPlayLB

    Broncco escargot for rear axle

    Hello all. I am in need of the little snail looking axle adjusters for a Broncco TX4. If anyone has them, please send me a PM and we can strike a deal!
  12. OND

    New Rear Shocks 10"

    This is a new set of shocks that I bought for my build off bike.....bolted up but never used . Shocks are 10'' from bolt hole to bolt hole... bolt holes are 3/8''. $40.00 and I'll ship them for free. Great for lowering a swing arm bike !
  13. tbird

    DB30s rear brake cable barrel

    I have a DB30s (Metal fenders) that I just picked up and the brake caliper and brake cable were messed up. I got a cable and caliper off a person on here and the barrel end that goes in the brake lever is smaller then the original barrel. He said he took it off of a DB30s just like the one I...
  14. T

    Powerdyne rail chopper rear fender

    Hello. Needing a rear fender for my next project, including the bracket from bottom of seat to fender. I have other brands of parts to trade or cash. Thanks in advance.
  15. J

    1968/1969 Rupp rear shock numbers

    Hello, Looking for the original 68/69 Rupp rear shock upper and lower Sebac shock mount numbers. Specifically the frame upper and lower cast mounts, Regards, Joe51
  16. S

    Bonanza Mini Buggy need a rear hub, 5 lug.

    Any one know where icould find a rear hub 5lug 1" bore? Thanks
  17. B

    Wanted: Stellar front and rear fenders

    Wanted: Stellar front and rear fenders. looking for Quasi style and Black Beauty style. Prefer clean but would like to see what is out there. 2 complete sets would be great. Thanks in advance. Thanks, Greg
  18. B

    Wanted: CAT rear fender for Hustler/ Duster chopper. Thanks.

    Wanted: CAT rear fender for Hustler/ Duster chopper. Thanks. Would like a nice complete fender. Please PM me with cost and photo. Will pay for correct piece. White fender from a S&S chopper and you would be my Hero! Lol. Thank you for any help or info.
  19. danford1

    Hydraulic rear shocks and spring rate questions

    There are a couple of other shock threads going but I don't want to hy-jack someones thread as what I want to know is different from the other threads. I'm building some mini's for the build off. Two of them are Sears bikes with a swing arm rear suspension. They just have the spring sliders...
  20. T

    Made a rear rack

    Just finished this. Pretty Happy with it.
Top