rebuilt

Any one know the proper compression reading for a HS50-67023. Just rebuilt one with new rings(measured proper gaps and gaps spaced properly), cyclinder honed, valves lapped, valve guides w/in specs, valve gap w/in spec. Im only getting about 60 psi. Shouldnt it be more than that?

Up for sale is 1971 Arctic Cat Screamer. I just rebuilt the motor and have a video of it running on YouTube that I will attached. The bike is very complete but will need the correct kill switch, drive belt and air cleaner, I have the flexable center exhaust piece. This is a great bike to restore...

Chrome universal gas tank (chopper style) complete with mounting hardware and petcock valve. Never used. $70 shipped. 5-hp Briggs engine, rebuilt and never fired since overhaul. Needs air cleaner and muffler. $100 shipped.

Tecumseh H35 shortblock professionally rebuilt. this is a points and condensor block. Factory parts used throughout. Fresh .020 over bore, nos piston kit, rod and crankshaft. new gov shaft, crank seals, in valve, exhaust guide, recut seats, decked .025". ready to go. head, valve cover and intake...

Dunno what application it would be good for so dont ask :smile: I bought it not thinking for a very small CC engine and its just too big of a bore for it. It clean and not gunky, I think it may have been rebuilt and ready for service but its been along time since I bought it. $28...

I have a 1970's Ruttman Ugly Mini Bike that i have completely rebuilt. Frame, fenders wheels bars pegs levers are all freshly powder coated. new bearings new seat new brakes new chain new clutch new tires. All hardware on this bike is either stainless steel or grade 8 hardware. This bike has...

I rebuilt this little survivor and gave it a mild custom/rod look to it. Let me know what you think!

Got very little in it . Any idea what it is ? What kind of brake system should it have ? Currently no brakes . Enginewas supposedly just rebuilt with no hours

Howdy, selling my 3hp Briggs Ive been working on. Nothing wrong with it, just found a different engine thats brand new with steel cyl. This 3ho has been mildly ported on the intake and just deboogered on the exhaust. Bore still has crosshatch from factory! All new gaskets. Original carb and tank...

Labor to align bore .020 over $100.00 ( done by a shop ) Piston, rings, circlips and pin $45.00 Valve springs $10.00 Gasket kit $20.00 Points and Cond. $10.00 Oil seals $8.00 New carb $75.00 Total parts $268.00 My labor $200.00 Included Lapping valves and assembly Total price...

Hey guys I need some help, I just rebuilt a 3hp Briggs I/C FH and it's not firing. The carb is sucking up the gas and getting it to the plug because the plug is wet, and it has really good big spark, but it won't fire. :doah: I know for sure that I got the cam and the crank gears lined up...

This is a completely rebuilt 5hp briggs engine for sale. Block was blasted and honed, good port job, milled head, great little cam, tillotson hl314 gas carb, fuel pump, strait pipe, new breather and tube, clutch/ chain guard, powdercoated tin and all stainless bolts. engine only has break in...

Its weird Im getting fuel up to the petcock valve but not inside the bowl. When I separate the bowl from the other half of the carb with the fuel lines still attached I can get fuel coming out of that hole when I open the valve , but once I put the bowl back on ,no fuel is present in bowl. I...

this engine was just rebuilt and has less then 30 minutes on it. engine was ported, has good slapper cam, good springs. ignition advance 2 degrees. all new powdercoated tin. runs great with great response. Im selling engine complete minus carb/intake and exhaust. buy this engine, install your...

This thing is beating the snot outa me. Got it back togeather and it will pop at idle with the choke on. Move the choke back one notch and it will start and run 20 or 30 seconds. If you whip the choke off it quits. I have a brand new oem carb. on it, both needles set at one turn. Nothing changes...

I've got a freshly rebuilt 5 hp Raptor motor complete with exhaust, carb, minibike throttle kit and mounting plate. $250 shipped anywhere in the U.S. Email for more information or pictures. thinkracing (at) yahoo (dot) com

Im selling my hodaka ACE hodaka 90 engine on ebay. Its completely rebuilt and redone. Hodaka engine Ace 90 bonanza mini bike completely rebuilt excellent condition | eBay

I recently rebuilt this engine and have already sold the carb & tank setup. It came off of a Craftsman Rototiller rental and was said to have starting issues. When I took it apart it was easy to see that it was well maintained with frequent oil changes. Clogged pickup tube seem to be the...

So I rebuilt the 5hp Briggs this week. Now I can't get any gas to fire. I wonder what now?:shrug: I did not rebuild the carb, but did give it a good blow thru with the air hose, and replaced the carb to tank gasket. I pulled the plug after many many attempts to start it. There wasn't a drop of...

All carbs listed have just been completely taken apart, cleaned, rebuilt, fulcrum arm set, pop off set, all new stainless allen head bolts/screws, and all come with filter adapter with filled in and blended screw holes. All very nice carbs, ready to bolt on and run. They have had NO fuel through...