rod

  1. boatguy

    2 cycle rat rod toad

    Mocked up my new Tecumseh AH58 2 cycle engine into a Ruttman Toad.Am going to try this 10-420-5 inch tire in the rear but it may be too wide with the spocket--will see. Question with a 2 cycle what gear should I run--12/60 of higher on the bottom as this engine revs a lot higher than a 4 cycle...
  2. R

    hi all im rod from london england

    need some help guys I have a fantic bronco I had when I was 6 , its a fantic bronco tx6 with the round tank and the 4 speed two stroke marreli engine, im restoring it for my grandson and in dersperate need of a exhaust, any help please, cheers
  3. cpu77

    Can you buy Arc bilket rod bearings?

    I bought a new rod and engine almost 5yrs ago. It's brand-new.... I just got around to assembling all the parts. In doing so I discovered the ARC rod bearings had become corroded. Do they sell new bearings or is the rod junk? Specs are as follows . Rod markings are ----ARC #6270...
  4. B

    billet h50 rod on ebay!!

    Not mine, but stumbled across it looking for ohh parts. Neat looking piece!! Tecumseh Billet Con Rod H50 5HP Motorsport Rupp Taco Ruttman Mini Bike TT500 | eBay
  5. lelej1080

    WTB Billet ROD AND FLYWHEEL for honda gx200

    looking for the last few parts to my build. In need of a billet con rod for a gx200 and a billet flywheel. Let me know what you have!
  6. Bgw tri rod

    Bgw tri rod

    Mid restoration
  7. BGW tri rod

    BGW tri rod

    Mid restoration
  8. P

    Billet rod install

    Can someone give me directions on how to install the billet rod? I can find videos on everything I need but the rod. I have found one video where a guy uses plastic gauge string and measures the "oil clearance". Is that necessary or can I just bolt it right in?
  9. ugmold

    WTB: H50 Con Rod and Piston

    WTB: H50 Con Rod and Piston: part# rod=31295C piston 33312B The engine is Tecumseh H50-65077H serial 8198 14298
  10. ugmold

    Tecumseh H50-65077H broken rod and piston, looking for part numbers

    Hi folks, I have an H50 with broken con rod, damaged piston. The crank has cooked aluminum on it I hope will clean up using muriatic acid. Not sure what part numbers to look for, the rod has 25-0-13 on it, don't see one listed on eBay. The engine is Tecumseh H50-65077H serial 8198 14298...
  11. T

    Hot rod Baja build

    New to forum need help figuring out how to post my pics.
  12. T

    Hot rod Baja build

    New guy to forum
  13. CJdoodlebug90

    212cc preadator knock

    I have a non hemi that has developed some type of knock. Before the knock i had a hard time setting valve lash, but eventually got it. Went out and did a full pass to test it out and came back with a slight knock. took the head and pull start off and turned engine over slowly by hand and it...
  14. H

    HS40 Billet Rod

    I'm doing a hop up of an HS40 at the moment and I wanted to report my findings on billet connecting rods for these engines. Nowadays, nobody sells new billet connecting rods designed for the HS40, along with its under bored and over bored siblings, the H35 and HS50. ARC racing does sell a billet...
  15. Twid

    Billet rod predator212 non hemi

    Any one have a good video or pictures for the install of said part? I'm worried about crank position when installing new con rod. Any reference is appropriate please an thank you!
  16. Droydx

    Rat Rod or buff it out?

    I just got this one up and running. It was a friend of mine's, who passed away. The guy didn't believe in check ups, or doctors, and it caught up with him. Anyway, it has a low hour Briggs 5hp and a nice Comet TQ set up. I didn't like the stock briggs carb/gas tank set up, so I replaced that...
  17. TankforGod3

    arc Performance cast rod?

    I've been checking out connecting rods for my engine and I came across thishttp://www.OldMiniBikes.com/?target=product&product_id=32297 it says its a performance cast rod from arc. Has anyone used thisk? are they worth anything? How many rpms will it hold up too? They are a whole lot easier on...
  18. minibikin'

    Gasket Goons Hot Rod Bash

    If any local friends are looking for something to do this Sunday, IronHonky, Notsominibike and myself will be setting up a minibike display at the Gasket Goons Hot Rod Bash. Sure to be a hell of a good time. Pre 1969 rods and classics, food, pin up contest, valve cover racing!!! Weather looks...
  19. D

    arc billet rod and flywheel install questions

    Hey guys this is my first build it's a Doodlebug with predator engine six and a half horse but when I was taking the cam out I notice that the lifters had came out as well but I didn't see you which one was which? Does it matter which lifters go where? And also before I got the billet rod and...
  20. J

    h60 vs h50 rod length

    Hello, Just verifying Is the H60 connecting rod slightly longer or shorter than the H50 rod? I did not label when I disassembled a few of each. Thanks, Joe
Top