shaft

  1. B

    Old 2 stroke with small shaft

    Hey people so basically I have a tiny little 2 stroke Fox Motori Engine and it has a 12mm keyed shaft I was wondering if I would be able to put a normal centrifugal clutch on it as I have seen people put a centrifugal clutch on the little Ohlsson And Rice engines so is it possible to put a...
  2. M

    installing a clutch on a keyless shaft

    Gents any tips on installing a clutch on a keyless shaft? Have a 3hp briggs from an edger but it does not have the key on the shaft.
  3. B

    Clutch for a 9/16 shaft?

    Im looking for a clutch for a 9/16 shaft. Anyone ever heard or now where I can get one?
  4. Dr. Shop Teacher

    Jack shaft brackets for a VT525 (Trail Bike)

    Anybody have a set laying around or measurements to make them? I have the large swing arm brackets but not the plate-like brackets for the jack shaft and driven pulley. My Gilson collection keeps growing....:ohmy: Thanks in advance!
  5. JohnnyTillotson

    MTD Trail Bike jack shaft help

    I have in the place where the jack shaft goes this bolt that goes half way through. What is this? Does it need to come out before i put it in or is it part of the jack shaft set up and needs to stay in? Outside: Other side on inside: Also i see this jackshaft has a groove for s...
  6. JohnnyTillotson

    MTD Trial Bike jack shaft/ TC covers

    I need a jack shaft, sprocket, and driven for a MTD Trial Bike (The bigger MTD with the funky front fork rake) also need 2 TC covers for these bikes.
  7. 6doggie3

    Trail Horse ss 300 jack shaft plates

    Looking for the just the movable bearing hanger plates? I thought OldMiniBikes sold them but now it seems to be a whole kit? Thanks!
  8. C

    Baja 165 - Clutch Shaft Bolt Thread?

    Hi all, I am getting close to having the Baja 165 running around! Got some help recently and got the bike running. I am going to be putting the clutch on, but I am not exactly sure what the bolt threads are for the engine shaft that supports the clutch assembly? Some folks are saying...
  9. Thad

    Aux shaft alternator generator?

    I have found a few Tecumseh engines with the second shaft on them. It is easier and less expensive to buy one of these than a lighted coil motor for most projects because I live in a winter wonderland. I was wondering because I am cheap if anyone has chosen to add an alternator or a generator...
  10. myjunk

    2 1/2 hp Clinton engine wanted horizontal shaft

    Looking for a Clinton horizontal 2 1/2 hp engine. I need it for my little gen minibike. Thanks
  11. E

    gear ratio for taco with jack shaft

    need help with 1/8th or 1/4 mile gearing. i dont have the cash to buy 20 different sprocket combinations. i have a taco minibike with the jack shaft. i do not want to eliminate the jack shaft. any help will be greatly appreciated
  12. chipper

    Jack Shaft

    Good morning guys , the adjustable jack-shaft kit from OldMiniBikes , do they use a 1-3/8" O.D. bearing ? Thanks
  13. B

    Jack Shaft kit

    I'm sure it's been asked before but does anyone run a Jack shaft kit on their bike? I was thinking about adding it to my 212 predator engine but I wasn't sure if it would be worth the $$:confused:
  14. N

    WTB Gilson AC Montgomery Wards Gas Tank and jack shaft

    Looking for a under the seat / frame gas tank. Also a jack shaft. Thanks
  15. H

    WTB tecumseh h35 crank shaft

    Want to buy a tecumseh h35 crank shaft # 30946 for a h35 45280H if anyone has one they want to sell I'm in the market
  16. H

    Tecumseh h35 crank shaft

    I am looking for a crank shaft for a tecumseh h35 part no. 30946 if anyone has one they watch to part with let me know thanks for any help
  17. JohnnyTillotson

    Making a jack shaft questions

    Ok so the paint dried enough to throw the motor into the frame and visualy see how its going to line up with the sprocket. Its going to be too close even when I install the spacer I ordered to lift the engine over the frame rail that prevents the blower housing from moving far enough over...
  18. S

    clutch question for metric shaft

    I have a 5hp Suzuki 2 stroke from a toro lawnmower that I want to use for a future project. The problem I have is the shaft is 25mm and a 1" clutch is .016 to big. I don't want to mess with the crank so have decided to modify a clutch to fit, does a 3/4 bore have enough material to bore out to...
  19. R

    Fox Jack Shaft

    Sooo I stared at this today scratching my head as to how to get it out of it's rusted location. Can someone get me some pointers as to how to get this Jack Shaft out of a 70's Fox? Did I do a search first? Yeees so no flaming...well maybe a little.. I am new, but I'm wearing Asbestos Underwear...
  20. P

    New Honda GX390 Horizontal Shaft Electric Start

    I have a new Honda GX390 horizontal shaft electric start engine. I was going to mount it on a go cart, but have recently purchased a CJ-5 so my little toys are getting sold. I have the owners manual, factory tools, and some other misc. paper work. I mounted a clutch on the shaft for fit up, but...
Top