slant

Hi there. Looking for an Tecumseh HS-50 slanted intake manifold to complete my MTD mini bike build. Been looking for months now with zero luck. Tecumseh PN# 33669 Have paypal and will pay top dollar for one. Thanks.

I decided to put a HS50 on my Rupp R2 while I get the 10 HP vibration issues worked out. I partially freshened up a low use 50 I have cleaned and lapped the valves, put in new points, condenser, coil and carburetor, when I tried to start the 50 it was difficult to get going and when I dialed in...

Hey folks. I'm in need of a HS50 slant intake manifold for my 1971 MTD mini bike build. It's the last part I need to complete this build. Please let me know what you've got and I really appreciate it. Cheers:thumbsup: Scott

I read the Tecumseh HS40 motor takes 21 ounces of straight 30 oil. (My motor is an 80's model) I have it mounted on a slant on my FOX Spoke Wheel mini bike. I poured in 21 ounces of oil & the dip stick has it above the safe line. (While slanted) the oil is pretty close to the fill hole, so...

Hi there. Still looking for a Tecumseh HS50 slant intake for my 1971 MTD model 520 mini bike. Let me know what you want $$ Thanks.

Getting closer to finishing my 1971 MTD build and I'm in need of a Tecumseh HS50 slant intake manifold. If anyone has one that they would part with, shoot me a PM with a price please. Thanks.

Looking for a slant intake for a HS 50 , radams7425@aol.com

I hate to sell but I am in need of some quick money in my PayPal account asap please. Can get pictures this evening, nothing is broke or wrong with the intake. I figure this will be a quick sell. $45.00 shipped please pay as friend's. PayPal is lotof2@hotmail.com

Hello, So I'm working on this 1971 , 4hp Tecumseh in a Trail Flite. Been sitting for 25 Years, So I get a New carb kit. Replaced everything even though all it really needed was a new diaphragm. The Dam thing floods the intake & carb, New needle, Seat and seal. Had this carb off...

The slant intake from black widow motorsports states that it is for both HS40 and HS50 engines. Is this possible? I am wanting to know if anyone has tried the slant intake listed on an HS40 engine size using a floated carburetor that used to run an unslanted diaphragm carb setup.

Does anyone know if a slant intake from a H 50 will fit a H 35 ?

I'm looking for a slant intake for a Tecumseh H 35

Nice Hs40 slant intake. media blasted $40 shipped. Taylor exhaust Has been repaired. $42 shipped

Like it says up there. The real deal hs50 slant intake and original carb. $85 shipped

So I was reading a thread on this OldMiniBikes site yesterday from fall 2014 by Matt2. I was rather disappointed that all the photo links were dead as far as his Wife's bike. Instead they were redirected to OldMiniBikes Site so I haven't a clue how this bike turned out visually speaking. As someone...

Looking for the intake manifold for a Rupp H35. The slant that makes the carb level. :laugh: Thank you for any help.

Like it says up there. I can pay cash. Trade parts. I have a slant hs40 gem straight shot intake of H25/35 straight shot intake to trade. Other parts. Let me know.

Does anyone know how much oil to put in a hs50 for a black widow Rupp. They were run with dellorto carbs with no governor. Just wondering if I put the hs50 I built on my Rupp how much oil I should put in.

I need a Taylor exhaust for a hs50. I would love the kind with the slanted tip. Like they came on Ruttman I have a really nice chrome hs slant exhaust I want to trade.

I am in need of a hs40 for a rupp roadster 2. Do get me wrong I'm not looking for the original motor. Just a nice hs40 tec to put on my rupp for winber. I'm not trying to break the bank if I get find on for under $100 I am just going to throw a predator on it. The motor I had for it ended up...