820

Looking for the screen that protects the flywheel. It is formed to fit around the starter cup as seen in pics. Let me know if you have one. Thanks

HI all, Anyone here ever tried mounting a US motors (West Bend 820) on a 1971 Rupp Scrambler? That sounds like it would be a fun combination. Thanks, Bill

US 820 motor with repro engine mount sale is for one engine, $400.00

I'm in need of an engine mounting bracket/stand for a West Bend 820 motor. Any leads or info on where to get one, would be greatly appreciated.

I finished rebuilding the West Bend 820 on my Chrysler Sno Runner. Both the recoil starters I have do not engage the "Cup", which has many gouges in it. When looking for a replacement cup I saw one advertised as a right hand "Cup". Is there a difference in starter cups on WB right and left...

Hi.. Does anyone have a GEM 12v intake manifold or similar manifold to run a tilly HR single carb on a WB 820. Even just the base and reed block will do .... Thanks

Mc 70 setup to run alcohol, would like to trade for a west bend 820 setup for right side drive.

West bend 820 Motor for Go Kart, Mini Bike, or Sno Runner. I have had this for a few years and never used it so it is up for sale. I was told it has a newer redone carb and has protective covers on intake and exhaust openings. $375 plus shipping.

Looking for a west bend 820, CCW rotation while looking at the pto side. Will consider all conditions

Used WB 820. CW rotation (looking at the PTO). This came off of a Sno Runner so it has a light coil. Stepped crankshaft, I believe it's 9/16" down to 5/8". Tillotson HL320A Carb. Carb is nice and clean, not gummed up but I'm sure it would need at least a gasket kit and a good cleaning. Bore...

Before I post a "For Sale" of this stuff I would just like to know if there is any interest. My reason for asking first is because these things really are not something most of you tend to lean towards to power mini's but since I have been here sooo long and like you all figure I will ask...

WTB early West Bend 820 Engine ID Plate that is held on by two small screws to the flywheel air shroud. If you have one let me know and calling me is the best way to reach me. Mike Cates, CA. (760) 473-6201

Looking for the following parts to complete a TACO 55 WITH HOT SAUCE OR A TACO 99 fitted with a WB 820 engine: 1) The original long round domed ends gas tank with cap. Petcock also if you have one. 2) The correct original air filter used on the WB 820 for these 55 and 99 models. 3) The...

Looking for a Taco series 1, 55 or 99 with hanging engine. Prefer the 99 with West Bend 820 but let me know what you have. Serious buyer. (760) 473-6201

Vintage ORIGINAL West Bend cast aluminum mount for 610 and 820 engines. Includes the steel upright mount which allows you to clock the motor every 22.5*..the slots also allow for height and pitch adjustment. Not to be confused with the reproduction stuff... Getting very hard to find these...

Vintage Kart Vintage Mini Bike U s Motor Power Inc Power Bee 58041 | eBay So when he found it in the original box, a Tecumseh pull starter must have migrated in there, while the gas tank and mount migrated out of there. While all that was happening, the engine rebuilt itself into a later...

Nice complete WB 820 from a Chrysler Snorunner. CW rotation, Tillotson HL320 carb. Stepped crank, also has light coil. Been sitting on the shelf for years, was told it came off a machine with very little use. Great engine for your build off bike:thumbsup: $300 plus shipping Located...

looking for the cylinder head cover for 820 west bend with angle plug, want one with no damage, thanks

Can one change the direction of rotation on West Bend 82030?

I was given what appears to be a water pump, after some research it appears to be a West Bend 820, I do not have a picture, however, DZLBIKE posted a picture of one that looks identical to the one I have, http://www.oldminibikes.com/forum/engines-modifications/58383-2-cycle-engine.html, The guy...