bowl

  1. B

    Diaphragm or conventional bowl carb?

    What are the benefits of a diaphragm carb? Are the better than a conventional Tecumseh carb. Just wondering:)
  2. Sprocket86

    Tec carb bowl vent help!

    If I delete and cap off the primer bulb nipple on the carb body, will I have to enlarge the tiny vent hole that's drilled in the side of the carbs main body? What symptoms would this cause if I were to leave the tiny vent hole unaltered if the primer line nipple was capped off? I...
  3. Mikuni round slide vm22-133 bowl

    Mikuni round slide vm22-133 bowl

    Genuine vm22-133 float bowl
  4. J

    Dellorto float bowl top

    Looking for a good used float top. It would be the one with the float needle and pin/arm. thanks
  5. old shed finds

    Briggs 3-5 HP Updraft Carb Fuel Bowl Needle Jet leak.

    Hello Guys.. Anybody fight the briggs 3-5 HP Updraft Fuel Bowl flooding? Horizontal Tote Gote 5 HP Engine, The Float was tested Hours under Gas to check for leak and passed ,,, We think it Is leaking at our needle valve fitting gasket.Anybody else have this problem?
  6. zeeman

    Tecumseh H050 carburetor float bowl and float

    The spring drain thingy broke on mine, plus it is dented. If you have a special place that is good to order from, I'd like to hear about it. Will take used parts too. Thanks. Here is the carb.
  7. CJdoodlebug90

    Car leaks after jet install!!!!!

    I was running .028 size jet and noticed i had bad throttle reaponse. So I ins5alled a .032 jet....runs perfect but now carb leaks. It seems like its coming from the top of the bowl. I made sure I put rubber seal back in... I need help. Upgrades: dyno cam. 18lbs springs. Header. Air filter(no...
  8. Commonrail

    Briggs flat head 5hp tank question.

    Is there any coating you can use to fill up the holes that the rust enhanced in the fuel bowl in the tank?
  9. Sixpac440

    Honda ES6500 Generator wont stay running ...

    The crank case was full of gas and oil. The gas had migrated from the tank to the crank. Changed the oil & filter. Removed the carb, pulled the float bowl, gently cleaned the jets with WD 40, air and a small wire. The bowl was clean when 1st disassembled. 1-1/2 gallons of fresh gas was put...
  10. FloridaMiniBikes

    Tec H35 Blower housing/starter, tank and carb

    nice units, I can't get the pictures to load. toss me a pee em with your email and I will send. $40 shipped to U.s. 48 states. Carb is float bowl type and may need a cleaning or rebuild. Tank is black plastic with center fill.
  11. 125ccCrazy

    Has anyone ever had one of these adjustable main jets for a Mikuni?

    I was looking on ebay for a jet holder for my vm22 since I misplaced the one for mine and I came across this.... hopefully it fits the bowl on my carb and works well.. This would make tuning the carb easier that having to keep trying different main jets..... Vintage Motocross MX Precision...
  12. H

    Predator 420 carb leaking

    I can't seem to find what's causing the carb to leak. It will slowly drip fuel from the float bowl until the entire tank is drained onto the ground. Thus far, I've tried changing the fuel shutoff valve gasket, the float bowl gasket, and the three carb gaskets with no success.
  13. S

    Predator 212 Carb Bowl Gasket???

    Guys, Anyone know where I can get a replacement carb bowl gasket for the Harbor Freight Predator 212 engine? I am having a hard time finding it online. Thanks.
  14. T

    H35 Carb Bowl Needle and Seat PN# Please?

    Gang, Can someone tell me the correct bowl needle and rubber needle seat kit pn# number for an H35? The engine model is H35-45158E if that helps any. The engine is on my '67 Rupp Electra. I think the kit pn# is 631021, but I'm not for certain. Thanks in advance for any help!!:thumbsup:
  15. markus

    tecumseh late model primer bowl carb?

    I picked up a Sears labeled Tec the other day in a bike/parts buy. its a side popper 3 or 3.5 have not checked the numbers yet. its got one of those primer bulb bowl carbs on it, of course the bulb is rotted and gone. Normally I have no use for something like this but since period correct...
  16. H

    Cleaned out carb and gas tank but now no gas is getting in the bowl

    I have a 5 hp power sport engine that was running only if I kept pushing the primer blub. I removed the carb and cleaned out the holes in the bowl bolt that were pluged up. I removed the float and needle and sprayed carb cleaner through all the holes in the carb. I also cleaned out the gas tank...
  17. J

    wanted: DeLLorto UA19S float bowl

    Searching for a float bowl and choke assembly. As well as the 7.5 gr float in my other thread. Willing to trade for an H50 allum lighted flywheel and stator or pay in cash. Thanks, Joe 51
  18. 4

    need carb fuel bowl nut 167

    I need a carb fuel bowl nut number 167... snowblower,i think the last year tecumseh was in business,carb has no numbers for IDing but at least the bowl nut is numbered 167... Thanks
  19. G

    Briggs Glass Sediment Bowl

    I am working on a Briggs 143302 and a 142302. I want to keep them as original/vintage as possible. I need the fuel filter/glass sediment bowl part #99910 for both. I can't find any, but on Ebay I find lots with a different part (690612, 393169) number that LOOK identical in the pictures...
  20. james c

    vibratory bowl

    bought this today, i cant wait to try it out, any idea on media? looks like rims should fit easily
Top