Register

User Tag List

Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 3 of 3 FirstFirst 123
Results 21 to 29 of 29
  1. #21
    Senior Member markus's Avatar
    Join Date
    Apr 2008
    Location
    Southwest Florida
    Posts
    10,861
    Mentioned
    57 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    Quote Originally Posted by capguncowboy View Post
    As far as I know most of the H25, H30, H35 and HS40 engines had starter teeth on the flywheel. The only exception to this is the lighted engines. I've never seen a small frame mini bike engine with a starter though.
    Just the HS40 non lighted flywheels- the teeth were standard, great way to quickly tell them apart in my bin of flywheels . They cast them into the first HS50 non lighted flywheels too that were aluminum. But that flywheel only was made for very short time before they updated to the stronger and probably cheaper to make steel wheel. I dunno how they work with an electric starter but they had that side mounted recoil for vertical engines that utilized the teeth.

  2. #22
    Senior Member
    Join Date
    Oct 2015
    Location
    PA
    Posts
    615
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    terningeugene,again as far as I know that style small tire/wheel MTD never came from the factory with a 5HP engine.

  3. #23
    Senior Member markus's Avatar
    Join Date
    Apr 2008
    Location
    Southwest Florida
    Posts
    10,861
    Mentioned
    57 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    Quote Originally Posted by terningeugene View Post
    Markus,
    I just purchased two diaphragm carbs off ebay and I want to use them on future motors to be correct. What is the Tecumseh part number of the standard intake like the one in your picture above and does anyone re-pop them that you know of?
    Thanks for the info..
    I found some of the 32859 versions in my parts bins this morning, I listed one on ebay if you end up needing one (just search that part number in tecumseh parts...its the cheapest one listed). Good luck with it

  4. #24
    Junior Member terningeugene's Avatar
    Join Date
    Nov 2017
    Location
    Pleasant Prairie, WI
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    I looked it up on Jack's and they are calling for a TEC #33301 Intake but for use with a float bowl type carb since the diaphragm carb is NLA.

  5. #25
    Junior Member terningeugene's Avatar
    Join Date
    Nov 2017
    Location
    Pleasant Prairie, WI
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    Thanks Markus....Will do!!

  6. #26
    Senior Member markus's Avatar
    Join Date
    Apr 2008
    Location
    Southwest Florida
    Posts
    10,861
    Mentioned
    57 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    Quote Originally Posted by terningeugene View Post
    I looked it up on Jack's and they are calling for a TEC #33301 Intake but for use with a float bowl type carb since the diaphragm carb is NLA.
    Yea, thats the slanted one for the 20 degree float carb, there are 2 different standard intakes that were available, on had a rounded top and one was more square, That square top I just put up sold in a few minutes (I guess your not the only looking for one), I just put another up though, I found like 3 of them in one of the parts bins.
    Last edited by markus; 04-19-2018 at 12:52 PM.

  7. #27
    Junior Member terningeugene's Avatar
    Join Date
    Nov 2017
    Location
    Pleasant Prairie, WI
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    Markus,
    Is this your Ebay listing with the standard intake? Please advise and I'm all over it.
    Used Tecumseh Engine Intake Pipe 32859 (Obsolete)
    Thanks again OMB!!

  8. #28
    capguncowboy's Avatar
    Join Date
    Apr 2014
    Location
    Bluff City, TN
    Posts
    5,980
    Mentioned
    8 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    Quote Originally Posted by terningeugene View Post
    Markus,
    Is this your Ebay listing with the standard intake? Please advise and I'm all over it.
    Used Tecumseh Engine Intake Pipe 32859 (Obsolete)
    Thanks again OMB!!
    No, his is much more reasonably priced

    https://www.ebay.com/p/Tecumseh-Inta....c100005.m1851
    I'm not afraid of death. I'm afraid of dying. I want to go peacefully in my sleep like my father did -- not like his screaming passengers

  9. #29
    Junior Member terningeugene's Avatar
    Join Date
    Nov 2017
    Location
    Pleasant Prairie, WI
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Rides
    0
    Got it on Buy It Now!! Thanks capguncowboy and markus and OMB. I'm liking this more and more now.

    HS40 Tecumseh Intake pipe 32859 (NLA) mini bike kart snowblower minibike 4hp

 

 
Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •