cable

I have '77 Briggs 5hp (#130232), and I am unsure where the throttle cable goes and what I need to link it to. Sorry I have no pictures at the moment, but some shots of how it goes would be really helpful. N.B; There is a sort of clip directly under the air inlet on top, which I am pretty sure...

I am looking to find out where to get these ends for my brake cables if anyone knows.I have been searching with no luck other then some call them threaded studs.Local bike shops look at me funny when I ask.Ant help would be great.:shrug::confused:

Is there a bracket I can buy to hold the throttle cable on the carb. Engine is a Briggs 3.5 newer engine. Thanks

I wasnt sure where to post this, but I figured this was the right place. I am looking for Break cables for a 72 Arctic Cat prowler/Ramrod. I need help finding some with the hardware to attach them to the break arm. All break cables I find have bare ends. I also need to know how long...

I just swapped a Tecumseh for a Briggs off of a tiller. I need help hooking up the throttle cable to my Briggs. Pictures would be helpful.

Hi, Can someone tell me how to hook up a throttle cable to the carburetor on my 1973 Harley x90? I know it hooks up through the top of the carb but how do i attach it to the slide? I have the shop manual but it doesnt show how to hook it up. Do i bend the throttle cable to hook it up to the...

Have a B&S 3.5 model # 91202 years ago I rigged the throttle cable up to a multi angled "lever" mounted to the side of the carburator (that is not the actual throttle lever with stop screw mounted on the top of the carburator) which has a combination of rod and spring leading to what I assume...

i need about a 140 inch throttle cable for my three wheeler, anyone know where i can get one?

Hello fellow OMBers, With the help of this awesome website, and its equally awesome users, I was able to finish fixin' up my 1969 Rupp Digger that I bought for $40. I took it for a 15min test drive to today around my neighborhood and didn't have any problems! With a frame that's more than 40...

So I've been searching this site for example photos of band brakes and how to mount them. I already have my mount all drawn up. The one thing that still puzzles me is how to connect the housing from my brake cable to the band brake. I understand how to connect the cable, but the housing needs to...

I'm looking to replace a throttle and cable. What's the difference between Lined and Unlined Conduit? Thanks

Wanted throttle cable for Mikuni 22. about 48" long.

Throttle cable for 7/8 bars $15

My rupp roadster has no cable or governor linkages and I am trying to figure out how it hooks up...It looks like the cable goes down to the little arm below but it seems like the cable would be on quite a severe angle unless the arm was pulled up pretty close to where the cable casing is...

I have recently gotten a Fat cat and the throttle cable was frayed at the end and won't stay on? What set up is best for this?...I could try to get it through a barrel holder again but it comes out... what has worked for you guys....something this simple shouldn't be such a pain in the...

250 amp welder i need about 200' 1ot-2ot wire,if someone would have some thats no longer needed, thanks,wayne. O used please. :smile:

I have some 50' rolls of new 1.5mm inner wire if someone needs some for a long throttle cable or choke cable . this has no outside sheath or ends for the cable , just the inside cable itself . If you need to make your own cable Pm me and I will cut you off the length you need and send it to you .

IF I need to cut a brake cable conduit shorter, what can I put on the end to make it looked "finished"? Will one of these work? see below

This is an effective way to end the frustration of annoying frayed ends of the throttle and brake cable. I used a mini torch that I also use for soldering small jobs, however, I assume an electric solder gun will do the same trick. The flux is optional as well. Before After Items needed...

Yeah I know, odd subject, but thats what they're called. I got these specifically for the application they are intended, but the shop I bought from had no idea how to attach them to the cable end. I'm assuming they would need to be crimped, but with what kind of tool? Regular wire crimpers...