ported

I have two new 14cc JT-07 clone heads that have been ported and polished. One has 28.5mm intake and 25mm exhaust valves, the other has 27mm intake and 25mm exhaust valves. Ports have a sand blasted finish, combustion chamber unshrouded and polished, & cut multi angle valve seats. Comes with all...

I'm looking for a ported big valve shaved head with all the work professionally done and ready to use for my Tecumseh overhead valve 5.5hp (ohh55) if you have you are willing to sell private message me.

I have a new 14cc JT-07 clone head that has been ported and polished for 27mm intake and 25mm exhaust valves. Ports have a sand blasted finish, combustion chamber unshrouded and polished, & cut multi angle valve seats. Comes with all new stainless valves, retainers and keepers, and your choice...

Over the years I have heard stories of a Clinton powered kart that was next to unbeatable. Knowing a little of the Clinton engine short comings I dismissed this tale along with the claims of Bigfoot and the Loch Ness monster. Recently I have acquired one of these mystical engines and with a...

Hey guys, I had a question about my predator. I searched and couldn't find the answer for my set up. My set up -212 non-hemi predator -nr racing ported 18cc Honda head milled .050 -cm push rods stock length -reinforced rocker arms stock ratio -.016 copper head gasket -lash caps -black...

hello everyone, I was wondering if anybody had any flow charts for a Honda gx160 cylinder head? either home ported or stock. I couldn't find anything, I need this for a cam grind reference

I did this little sketch in win paint to illustrate how a port roof could be modified.

I have a brand new 14cc clone head and a 18cc that has been ported and polished and milled .70. Which would be better to use for a racing setup. The other engine mods are: billet flywheel and rod 22mm mikuni carb 8* timing key black mamba cam cromo push rods champian rockers billet...

115$ shipped going a different way on my build

I have for sale a clone head off of a Champion clone that I own. I got a different size head and wanted to try something a little different, but this one did run real nice on my Champion. The Champion clones are nice clones. Included with the head are brand new valves, springs, retainers, and a...

gx160 head ported and milled

gx160 head ported and milled

gx160 head ported and milled

gx160 head ported and milled

I have for sale a clone head off of a Champion clone that I own. I got a different size head and wanted to try something a little different, but this one did run real nice on my Champion. The Champion clones are nice clones. Included with the head are brand new valves, springs, retainers, and...

Freshly done Genuine Honda ZH8 race head for sale. MDB Port work(prooven horsepower gainer) 27 by 25 SI Valves with lash caps Milled .050 making this 18cc head roughly 14cc's Unshrouded New 26 pound springs Billet keeper & retainer set HD steel guide plate New 1.3 stamped rockers...

hey guys i have a 18cc Honda head milled .090, mildly ported, stock valves, new 26# springs, 100.00 shipped.

hey guys got a real Honda head use to be a large chamber head was welded and reshaped to a small chamber head. fully ported milled .080 stainless SI valves stock size 26#pound springs aluminum retainers fresh valve job this head has been used but i cleaned it up and did...

GX200 22cc Clone head, Fully Ported and polished, Milled .065 thou, seats opened up with a 27mm intake, and a 25mm exhaust. Spring pockets cut, complete with SI Valves, 26lb springs, SI Retainers, and Suzuki Hardened locks....Head is fresh, doing away with all my small block stuff.....125.00...

I have a new 265 cam, springs... the cam was installed but never ran before going with a different cam...new old style ported stock carb with the adjustable air screw w/ spring.. Chr push rods.... $75 plus shipping