head

head light $25 shipped :thumbsup:

I need a head for my 6 hp Mitsubishi motor. please pm me with ur price I am located in Corona , CA

* Tecumseh H35 Head: Bead blasted, N' hot tanked. No cracks. Spark plug threads perfect. Slight chip :censure:on fin nearest spark plug hole. * Set of head bolts. * 3 NOS head Gaskets. * New NGK CS-1 Commercial spark plug * Motorsports blue, (Mallory) plug boot and...

Hello, I need some ARCO head tube bushings bad. Will pay good money thanks! These seem like steel but would prefer bronze but will take whatever I can get at this point lol 5/8" ID X .965" OD X 3/4" long Flange = 5/64" thick, 1-1/8" diameter Thanks for any info anyone could provide...

Hello, I have an ARCO that has bad bushings in the head tube. The forks have a little shimmy in them, and when I removed the fork bolt (brand new) it was worn all funny on one end of the fork bolt. Does anyone have a source for new bushings? They seem to be bronze. Thanks for any info you...

Head & Bolts. Hot tanked, with 3 New head gaskets Flat, no cracks, but has very small chip on one fin. Gas tank, with top bracket. a little beat up, but No leaks. Sidecover and Bolts. Cam, and tappets. But wait, there's more! A brand spanking new #35 master chain link. $60...

Does anyone have a couple of the spacers laying around that go onto the head bolt to support the top mounting bracket for the gas tank? For an H35. Thanks Tom

Hiya folks. I am allowing my almost 14 year old boy to do ALL the work on our minibike project. Its a GREAT learning experience for him, but I am having a heck of a time not helping him. So far, I haven't touched it, but I need an opinion. He practiced on a stock head with a dremel tool...

My onan will move back and forth a few degrees but it doesnt go all the way. its definetly rusty and crusty inside but the pistons move so does the exhaust valve.:grind:

I have an old (1971) 8HP Briggs that blew a head gasket. I machined the head, installed a new gasket, torqued the bolts. Now that the engine has run and cooled, should I retorque the head bolts?

This is my second attempt at building a welded hemi head. (first one I hit the seats welding and lost interest, sent it to race city tools to have a machining fixture made for hemi heads) I took a baseline flow measurement and again noted that the flow is no better than a regular head although...

So I got a 14cc head, and was wondering if the valves from my predator will swap over I believe its the 3rd gen has split valve keepers, was also wondering what fuel I should run. Can I run regular? Octane Booster? Thanks

Its cheaper off ebay. Would the gx160 fit for the predator 212? The one of ebay comes with all valve train components . Thank

I have a 7hp Powerfist engine like it says in the title but after making a post awhile ago apparently the 7hp just have a bigger bore or piston and I am curious if a stock GX200 head gasket is big enough or will I need an oversize? The CC is 208 on this engine. I took the head off already and I...

I have a 69730 predator with the std. compression height flat top from N.R in the motor. I am sure I'm 28thousands in the hole even with my +20 rod and I am running a 10 thousands head gasket. I'm also running the auto lite plug in it. I forget the number on the plug but its like 3910 maybe...

Ok i got a brand new box stock project engine just put in a black mamba cam a 22cc head milled .65 26lb springs and 26/25 valves this is my first engine I did I can't seem to get the valve lash set right when I tighten down on the 10mm head screw holding back the 14mm one the gap closes to...

For sale Carlisle Double Indian head tires ,pair NOS never mounted,used on Early Lil Indian's 4.10 x 3.50 x 4 Priced to sell $55.00 for the pair... plus shipping Paypal Gift option :thumbsup:

I bought this Franking Trapper for parts today from the Scrapper (off craigs).. Started looking it over when I got it home and much to my surprise, I found the engineering to be way above the average shade tree Engineer.. as a matter of fact the welds are perfect.. and there is no evidence of...

Bought a nice new head for 6.5 clone off fleabay that's a 14cc. You can tell it's 14cc by the way the chamber looks. Cause it's 14cc head would you mill the head some or just leave it alone and run it just like it is. By milling it wouldn't you go down more on the cc's ? Don't know how far to...

Here is a sweet affordable Ruttman for you guys and gals out there. Yes..I almost typed that with a straight face...almost.:doah: 1970s Ruttman Minibike w/new Predator 212cc Motor RUNS GREAT