honda

100% original. Starts easy and runs great not looking to sell. Would like to trade for a Trapper trail bike. Located in Taunton Ma. 45min south of Boston. Will travel

I ordered a stage one kit from OldMiniBikes for a Honda gx200 and the kit came with new Honda 18lb valve springs and I thought the stock springs were already 18lb springs or am I wrong?

Complete 22mm mikuni setup for Honda/clone/predator . Only slightly used in like new condition . Uni filter , and intake included $70 shipped

Hello, I need some help figuring out what year these two z50s are. The identification numbers are z50A-223900 and z50A-311122. I appreciate any help! Thank you!

Hi there. Going to be building up a DB 30 with a 6.5 hp genuine Honda GX200 and a Centrifugal clutch for a race series that another member on here has organized. I would like to lightly modify this box stock GX200 with a header/muffler pipe that will fit around a DB 30 or Dirt Bug frame...

Brand new ambush racing side cover fits Honda/clone/hemi $100 shipped . I have 3 and only need 2

I have been researching lighting coils for my 420cc Predator. I have read and been told that the GX390 stuff will fit. Can I get a little advice on out put. There is a 3 amp, a 10 amp and an 18 amp output setup. I figure the 10 amp will keep the battery charged and the lights on. Anybody...

Bare, cleaned, unneeded. My parts washer solvent discolored some, but it blasts back to shiny. $20 each plus a couple bucks for the mailman, unless you're accidentally in Flint MI. One is a new clone, with mild porting, others genuine. I need billet rods and cams for an HS50 and HM100

This is a quick power upgrade to either hondagx200/hemi or predator .. one of my own personal race heads . Real Honda zh8 casting with 27/25 stainless valves 26# springs , aluminum locks and retainers , real Honda rockers and guide plate ,and port work already done .. bolt on power $125 shipped

Just wondering if anyone has a great way to transport a Rupp Roadster I just bought 600 miles in the back of my Pilot? Thanks!! Pat

I could use a Honda or clone throttle linkage (arm) that has the cable stay attached to the arm. Hopefully one of you guys or gals has upgraded your carb and no longer needs this part and can help me out. Thanks, Owen

Got this engine on a bonanza i picked up. Not the engine for the bike. The govner arm was disconected and moved out of the way but its still there. The engine runs. 40bucks Pickup nj.

So this is my first Honda. I bought this for my son as I have always thought it would be a great starter bike. When it got it, it didn't run quite right. It smoked real bad. Long story short, I replaced with new parts the entire top end, piston & rings, and carb. I can get it to run, but it...

1971 Honda 175 i freaking love it. what a sprocket!

More goodies for sale, must go. 3.5hp Briggs, needs rings. $30 bucks. 3.5hp Tec long block, $30 bucks. Honda GC160 complete and running, $75 bucks. Baja 97cc with header, 2500 clutch, and carb work, 6hrs run time, great running stocker, $60 bucks. Briggs 5hp parts: Make offer. block, needs...

if this isnt allowed please remove! thanks so i have a honda st90 and after i ride it for about 20-30 mins it does this see attached video. carb says pz19 if that means anything or can get me more help, thanks! https://www.youtube.com/watch?v=tJy2SZf7j-k

Right next to brand new gx120 (3.5 HP) comes with #35 clutch. Location Troy MI $295.00obo

Genuine Honda 140 E-Tubes $6.00 Shipped anywhere In the US Free PM Or E- Mail Me astrowrench@gmail.com

Well, just found out Im short on my bills this month so time to thin the herd. I have a Briggs 3.5hp Industrial Plus shortblock. Needs a hone and rings...it was puffing oil on reassembly. Has a fresh paint job on it. Iron bore, single bearing, 3/4 tapped crank. Selling with old skool 3hp housing...