honda

Genuine Honda 16166-ZE1-00* These are the real GX140 Honda E-Tubes$6.00 Shipped anywhere in the Cont. U.S. Paypal or M.O. pm me or astrowrench@gmail.com

carb and recoil for honda gc 160/190 needed,they dont have to be spiffy,just useable. if you have the matching color cover i might could use that too. Thanks :thumbsup: also looking for: boonie bike rollers/or rollers with 10 inch wheels/tires.

I have a nice GC160 off of a power washer that had a dead head. Im not afraid of fabbing up a throttle for it, but Im concerned about the crank. It only has about 1 1/4 inches of useable shaft. If I were to use a stud, lock washers and Loctite, would that be acceptable? I really like this engine...

I have 2 running minibikes for trade or sale in Hbg Pa. I am looking for a Puch, Honda PA50ii or Tomas 50cc or below with title please. Feel free to drop me a line or message me.

Im building a Utility bike from scratch using a 5hp honda gc160 and torque converter. The tubing is all 1.25" mostly from a couple pressure washer frames. The frame will be rather intresting. The giant swingarm will hold the engine and everything and there will be a tray above the back wheel to...

Honda GX160/200 Camshaft from NR Racing (fits Predator motor) Camshaft, 252-0207: SPECIAL HIGH TORQUE GRIND FOR SMALL TRACKS, 6000 rpm, 22 lb Springs Required, 26 recommended. 10 to 1 Compression or higher recommend, however it will work with lower compression ratios. This is one of the best...

Looking for a throttle for a GC 160 motor Or a lead on where to buy one I didn't see at OldMiniBikes warehouse?

So need a carb for my honda GX160 . Need this toy running by the 22nd, can't find one in stock in a store near me yet. Anyone know if a carb of a predator 212cc will fit? Or know where I can get one overnighted from? :doah::confused:

Good running Honda gx160, needs to be cleaned up a little, gas tank has a few dents that could use a little body work to make it look new again...Runs good, no smoke.... $75

Hey guys, I am going to use an electric start, big block, motor for my next project- a kart this time. Anyways I want to save a few bucks and get the Predator 420 motor. BUT No one makes heavy mods for it. I asked some folks at OldMiniBikes warehouse, as they have GX390 parts and 420 Parts listed...

Was gonna put it on craigslist but thought I'd give everyone on here a chance first. It's a model 1979 honda atc 70cc 3 wheeler. I have the two original white rims also. Engine runs with a 3 speed trans starts with one pull usually. Mostly complete I think there were end caps on the air...

Just finished another Z50 , the white one , one more to go ,,,,,,,,,

Hello everyone, new mini bike user here. I've been looking online at Honda CT70's and some other knockoffs and was hoping for some buying advice. I found a 1991 CT70 on craigslist in my area for $1600. I'm not willing to spend that much but I was still wondering what the bike is worth...

My Baja MB200 Mini bike is a nightmare. I've had it for 3-4 months, and I've broken the brake drum, both chain tensioners, handlebars, chain, headlight, footpegs, kickstand spring, and now the crankshaft(?), twice. The crank/drive shaft snapped off while riding, so I drilled and tapped it and...

1971 honda z50 ,,1970 Indian jx-50 running good .going to windber.1971 z50.cheeftah 1400

Powerland PD420E 16HP Gas Engine Electric Start Horizontal Shaft | eBay cheaper and with electric start

Selling my 1981 Honda C 70 with only 485 miles on it. I had the carb rebuilt, oil changed, new spark plug and seat cover. It runs really well and also shifts great, rode it today. It has a few paint chips and minor scratches and will need a new battery. The tires are original and hold air, but...

Has anyone ever tried putting on a honda gx340 11hp engine on a frame before? What kind of clutches did you use? I mocked the engine up and it fits inside the frame but the shaft sticks way far out past the frame I know this could be fixed with putting a jack shaft behind the motor with...

hey gang I have a 1987 Honda xr100 rolling chassis for sale. I can bring it to windber. no shipping, local pickup ok too. asking 100 OBO, don't be afraid to make a offer, cash, paypal, bitcoin....must be paid for before I load it up. I also have a point style ignition system for it, flywheel...

Thinking about buying this guy said he just had it running now it won't fire up. Sounds like it wants too but just won't fire and run. What would be a good price to make an offer on this bike?