leaking

Think this might have something to do with it?? :doah: 25HP Briggs Intek Twin V.................that will cost him!!!!! Seriously what options does he have or should I say what options can I present to him. This motor is no good for obvious reasons. A new briggs will cost him $800 not...

I have two Briggs and Stratton engines (91202 model) with the plastic cap. Both of them leak from around the rubber seal on the cap. I tried a new cap and it still leaks.:shrug: For my first one I used gasket maker suitable for gas and made another gasket, and put it between the rubber gasket...

Ive had several briggs that leak gas around the gas cap area(the older style engines with the metal gas caps). What is the best way to stop the this?

I have had this problem with both carbs that I have had with my engine so I doubt it is the carb. I have allan screws that are tightened to the max and a new gasket. The gas is coming right out of the base and even through the bolts. I have the tank pretty full could this make a difference? Or...

Hi, I have an H35 from an old snow blower that I put on a mini bike frame I purchased via CL. I noticed in the last week or so a fair amount of oil leaking where the engine attaches to the frame plate. It appears to be a bit heavier on the clutch side, but both sides are wet. I rode it last...

anyone no how to stop oil coming out of govener shaft and runing down back of bock. this hs40 runs good but oil leaking is not good.:shrug:

Hi I noticed oil leaking from this little hole under neath the carb . I thought it maybe an escape hole from too much oil. I took a pic it being cleaned and the other is while running. You might be able to see some oil running down. thanks

rebuilt the carb and rode it yesterday w/out any trouble after having set for quite a while apparently and then today it is flooding out and leaking gas from the air filter side of the carb... i mean really coming out of there too. i noticed (since i always install clear fuel line) that some...

I have a 4hp techmesh engine and when its not running the main air hole leaks gas anyone know how to fix it????:shrug:

I just built a gx200 clone, with an older gx160 head. I used the new gx200 head gasket. After getting it all put together, I can see the head gasket leaking (Puff out of seam when reved.) I removed the head, treated with copper gasket sealant and re-assembled. It is still leaking. My question...

Ok so I accidentally put too much oil in the motor and now the oil keeps leaking out of the crank case breather... how do I fix this? drain out some of the oil? any help will be appreciated tecumseh h30

so i have a new model hf clone 6.5. the one with the funny mounted gas tank, came with the all the carb crap on it, etc. its a mild build. goody list: arc rod and flywheel flat top piston, pin, file fit rings, all honda parts chromoly push rods agk .265 cam stock rockers 18lb...

Does anyone know of a solution to stop oil from leaking out slowly from the governor arm on my Tecumseh H35 .I cant just remove it ,because my daughter is riding it, otherwise I would. thanks in advance Mark...:smile:

I have a 6hp ohv power sport it runs perfect at high speeds but when ipush the gas hard the head sprays oil all over the whole back section but only at higher rpms is it the head gasket my engine has small mods and runs faster than stock please help me

I got a 22mm mikuni carb kit from nr and i am having some problems with it. i tried the 130 jet for clone but it ran like poop. then i tried the stock jet that i drilled smaller than the 130 and it ran a bit better but then it started leaking out the bottom of the float bowl and the over flow...

My 6.5 clone carburetor is leaking at the on/off valve. If off, it doesn't leak, if on and with the motor running it doesn't leak but if I shut the motor down an don't turn the gas off it leaks. Ive taken the two screws off that hold it on and the rubber four holed gasket looks fine, as does...

Posting this for a friend. Diaphragm carb (no float bowl)....replaced diaphragm, gasket, spring, 'needle'.....still leaking gas. He says gas is leaking out of everything.:doah: I dont know what to tell him from here on out. Figures maybe someone here might have some insight.:smile:

Ok, just rebuilt my carb with a new rebuild kit. The adjustable main jet drips fuel. I tried different o-rings, stacked two o-rings. Any input on curing this problem?:confused1:

Anyone know where I can get a new shutoff valve, mine is leaking

I bought a Robin America/Subaru Ex 13 engine last year. I installed a Briggs and Stratton fuel line shutoff. When the shutoff is on and the choke is closed gas sprays from where the carburetor joins the engine. If I turn off the shutoff valve it runs fine without the leaking. I can run the...