switch

I'm looking for a Ignition switch that mounts in the side cover in good condition.

I just purchased a 1972 Benelli Dynamo. Would anyone be able to post a picture of what the light/horn/engine kill switch should look like? Was the horn chrome or black? Did it have a brake light combined with the tail light? If so...could you post a picture of the brake light switch and how...

I ordered new parts for my restoration. This is by no means in like-new condition, but it IS original Rupp parts, and it is 100% functional. There is a wear in the brake cable where it goes under the engine plate, but it's superficial and doesn't go beyond the plastic cover on the casing. The...

I just ordered a Tav from OldMiniBikes and it's comes with a 12 tooth whatchamacallit.:doah: So my question is what would happen and is it ok to switch it to a 18 tooth whatchamacallit?

mini bike frame Hell the switch plate is worth more than that.

Working on a father/son project. Used kart has a box stock project motor and we are replacing the kill switch. I ordered a new one from BSP but the lead are different than the one that we took off the motor. The old one has two leads - one to connect to the coil, the other to ground. The new...

2hp Briggs and Stratton engine Model 60102 I found the wire on the ignition coil, hooked it up to a switch and grounded the other wire from the switch onto the engine. Pics provided Switch doesn't do anything

pickd up a used 6.5 clone this week. Has no spark. Disconnected switch and low oil sensor. It has oil in it. Still no spark. I took the coil off. Is there a way to test the coil? Thanks.

In need of one cat switch plate. Need the larger one like used on 400 and eliminator. Have $cash$ ready to send. Pm me with a pic and price.

I have a 1972 DMP Trailchamp with a Tecumseh 5hp. It came with a light but I know it is not right. It is wired for a 12volt light right now. I would like to rewire it back to original. I have all the parts, wires, kill switch, hi low switch. The original light is missing the bulb and switch on...

The engine is about 6 months old. It gets fire to the plug and the gas is going to carb so i figure its the on/off wiring on motor that is connected to kill switch but I am not sure. Has anyone had this happen to them? Any suggestions?

Hello, I need some help on how to wire up a kill switch on a 1966 Briggs 3 HP. I'm mounting the switch to the bars.

What are the 2 wires yellow and black hook to on the ignition. I don't have the right key swith. I bought one at Napa it has. m / s / b these are marked on the key switch. Thanks it's a 72 fos sundowner thanks for you help. Working on it right now.

Hello guys, just finishing up the TT500 and I have run into a roadblock on the wiring for the headlight switch. Does anyone have an idea or diagram of how the headlight switch is wired up on those? I figured out the "Kill" button but I can't seem to identify which wires are for the high beam and...

I'm using a drum brake on my Cat Endura project with a lighting Tec. and brake/tail lamp. I've seen the Rupp switches, but no idea how they mount, and not sure if it's a good way to do it. (Smash and O ring and short across contacts?) Definitely don't know where to mount it. Since the...

I need cat switch plates, both sizes. Thanks Joe

Hello, I just got my mini bike running with a honda gc160, I bought a kill switch and hooked it up to the coil where the old kill switch (used to hook up to old throttle and turn engine off when throttle was shut with a button) but it doesen't work at all, on or off. Is there anything im...

Azusa seat 3 bolt pattern, kill switch and mount for handle bars, 145/70-6 and 4.10/3.50-6 tubes, @nd honda metal gas cap. Thanks:boat:

:shrug:.... so so need a switch plate for a cat.... :hammer:

cat switch plate....:hammer: cash in fist