flywheel

I need a Tecumseh lighted flywheel for a HS 40 or 50 to fit a non points motor. Not sure if they are different between the years, mine has the squarish shroud with a bump out around the pull starter if that helps. Can get the numbers off the motor also if needed. Thanks, Owen

Looking for a couple of #31332 flywheels. They are aluminum type from H25-30-35 engines. they are clearly marked 31332 on the face of the wheel. They average around $30 shipped used from what I have seen and will happily pay that in decent usable shape Let me know, Thanks

I received a used flywheel from a very generous member here whose name will not be revealed until the credits of said movie. In preparation,the flywheel is going to be balanced, polished and magnafluxed or x-rayed to make certain no pre-existing cracks are present. In preparing for the...

I want to make a video and try to dispel or prove the flywheel myths, kinda mythbusters style. If someone has one they can send me, I'll gladly give honorable mention in the video. Thanks. Joe

1st post. Have done lots of reading here. I'm looking to build a high torque low RPM motor for a boat mud motor. I have a stock non-hemi on the boat right now and it bogs pretty bad and will only run 2000-2300 rpm with a full load. I need more torque to get it up on plane so the motor can...

I got a new one but don't have any instructions or info with it anymore. Or the coil bracket. What is the timing mark set at for the s2 gx390 flywheel ? And how do you use the degree wheel on these smaller engines. And a long shot but does anybody have a coil bracket or know what I...

Does anybody know if other Tecumseh flywheels can be used on a HS50 and if so, part numbers?

Hi need help took off my flywheel cover on my 3HP Briggs and now when I put it back on I can pull it's once then it's gets stuck ? what am I doing wrong ?

Anybody have a Tecumseh Flywheel for a lighting H25? Part # 32338. Thanks

Well I to been a while since I've been onsite, had some health issues and things kinda ground to a halt. anyway, I'm giving the bile a new lease onlife. New sprockets, chain, gaskets etc. While setting valve lash, I noticed a clicking sound when I rotated engine by hand. I seems to be the agents...

Anyone with a good Tecumseh HS40 610769A Flywheel. (this is the magneto version) I'm looking for a good usable one.

I have a PVL flywheel to install on a Ducar 196. Should I lap it to the crank or can I just install it and be good. Engine specs are, no governor, stock cam, weenie pipe with muffler, open air filter and carb jetted. Going on a Barstool so not much chance of sustained full throttle. Do I need to...

has anyone put electric start on an engine with a billet flywheel? if so what steps did you take? I'm thinking about buying the flywheel starter ring and having it machined to the billet flywheel however I have no idea how or where I can get that done. Just tired of almost pulling my shoulder...

I have a 1970s HS40 crank that has bunged threads on the flywheel end. I cannot get the flywheel nut to even start threading on. I am hoping to get a die and clean them up. Does anybody know what thread this is? Thank you for any help. Michael

Looking for a good used raceseng finned flywheel for a gx200 or new if someone bought one and never used it

looking to light up a 5hp for a small 3 wheeler I'm building for our Granddaughter, I thought some lights would be cool on it..

Wanted a Tecumseh HS40 or HS50 steal flywheel needed, must be off a generated motor & have full magnets, points style, with good fan blades, look at picture to see what i am looking for.. please IM me with price & we will go from there.. thanks

Came from none running engine of a baja so its not been tested. Free for whoever needs this just pay the Usps medium flat rate shipping.

needs a couple minor dings finished and the recoil assembly... not rusted out. $15 plus ship

with new points and condenser in the package..., no broken fins or magnets...coils all test good.. $125