removal

Ok, ok. Everyone has discussed and shown how to crack open the case and remove the centrifical weights and shaft of the governor from the clone and then plug the case. (great write ups by the way) My question is: Why can't we just disconnect the arm on the outside so it's not functioning...

Hi, After rmoving governor, Throttle is hooked correct concerning opening and closing but it feels like there is less turn when using the throttle grip on hanldle bar:confused:. Feels like maybe a 1/4 turn of throttle, I was wondering if this is normal because of removing the other pieces and...

Havent tried yet but how do I get the engine clutch off? They are an odd set-up.

I have the 97cc DB engine and need to remove the stock clutch. I have removed the bolt and washer from the end of the engine output shaft, but can`t get the clutch to move outward and off. I am sure there is a recommended method to this removal process. How about a little insight from you guys...

For you seasoned bikers this maybe apprentice stuff but for others could be useful. I was trying to get at a snap ring to adjust a belt drive. Since the ring was recessed I could not get a bite on it even after using various pliers and screwdrivers. I thought about punching the ring off...

lots of good info here

need to replace belt on speedway red baron. cant figure out how to drop jackshaft down. I removed bolt on oppisite side of driven on jackshaft and figured everything would drop. didnt happen. Im stuck. This:censure:ing thing is pissing me off. Thanks for any advice or help you guys have.

I came up with this idea for removing rust from the lower section of this Bonanza MB 1210 front fork which are rusted to the point of not being able to remove the lower spring section. It works by placing the front forks into the 1 1/2 PVC and letting them soak in a rust removal solution...

How do you get the crank out of this motor? This thing from the flywheel is holding it on and I already broke something on this bike by hammering so I'm gun shy now. Is this just rusted on or something else?

I have a clutch removal problem. i took out the straight square pin and the allen key bolt. Is there something else im missing or not spotting. The engine didnt have a bolt in the spindal at the end of teh clucth. I also took a flat head and gently tapped the clucth and it would rotate on the...

i need some help here i can not get my crankcase off and i can not find a lock ring or any thing the shaft moves with it help.:confused: i want to remove the governor

How many of you guys remove the Swirl from your B&S carbs? I've been tinkering with a clean, little 3.5HP B&S I/C for the DB-30 swap. I plan to replace the diaphragm gasket set on the side of the carb, before I button everything up. I was reading some information on how to 'Blueprint' a...

Hello i'm trying to find the dimensions for a briggs 5hp flathead fly wheel removal tool. But i cant find out the dimensions of the holes i need to dirll in the 1/4" thick stock. How far do the bolts that push on the flywheel have to be apart. And what size bolt should i use? :hack::weld:

Hi, I have a shucks baja mini, with a 5.5 jiang dong clone, that won't start after removing the governor. It would start on the first pull before I took out the gov. Can't figure out what I did wrong.. I took off the governor gear & flipper linkage. plugged the holes with 1/4-20...

i got a 5 hp briggs and was wondering what special tool i need to remove it. i am going to do the 3 hp flywheel install. any help would be great.

I have a new 6.5hp clone and i just can't decide to take off thee govenor or not on one hand i want speed but my friend said it will destroy the engine and isn't safe so im asking anyone that has is it safe? does it really damage the engine bad?

I have never taken off the rear wheel from the frame and i removed that little pin through the nut on the left side but when i take a wrench i turn it as hard as i can counter clockwise but it wont budge:doah: what am i doing wrong

hi there i have a tec h40 on my ruttman mini bike that i am putting together and was wondering if some one could tell me how to remove the governor on so it goes faster thanks

OK.....I'll admit I have never done it and now I have a few 5hp flatty Engines I Want to do it on. Whats the procedure? Just get rid of the Wind flapper in the shroud? Gut it and take the mechanism completely out? Yes I Know they could blow up. I'll take my chances. School...

Can anyone tell me how to remove the governor on a doodle bug 2.8hp engine? Thanks in advance!