Hi I bought a new engine from HF but it turned out to be hemi. Tried to find non hemi guy over there tells me that now they are only sending hemi. I am switching the flywheel with magnets and coil for lights that were on my HF 212 non-hemi to this. The flywheel is of exact same size in diameter...
While riding the torque converter broke luckily cover was there to protect me. Now I am stuck with a broken nut inside the shaft making it impossible to replace torque converter.
I am trying to drill.
I recently replaced the belt with this https://www.homedepot.com/p/STENS-New-OEM-Replacement-Belt-for-Hoffco-Comet-994-70-Hoffco-Comet-203589A-Hoffco-Comet-203589-Murray-12-8487-255-299/314222529
Now the torque converter I hear rattles when I turn on bike and I am not able to drive it fast...
I was riding today and bike was jerking and then the rear wheel locked up. I had to put in suv to take it back. I cannot even walk the bike. The wheel moves an inch and then it is totally locked up. Does anyone have any suggestions on what could be wrong?
I am suspecting it is either chain...
Hi minibike freaks
I have a minibike that starts jerking and I do not feel it goes the same speed it used to go before. When I stop at the sign and give throttle, I get a jerk and seems the bike front not keeping with the back.
I have a torque convertor, rejet, air filter and racing spark plug...
Hi I am trying to put the led bulb in the headlight along with the rectifier. Anyone on here knows what is the exact match?
Item: X98-0770 Baja Motorsports: 165-666 / MB200-150
https://www.vmcchineseparts.com/products/headlight-for-massimo-mb200-mini-bike-version-82...
I have a predator 212 with a modified jet, autolite spark plug AR3910X, and air filter I am wondering what is the correct firing pattern? I have the tachometer at 1p2r equivalent to 4 stroke 1 cylinder. The RPM is at 4500 on idle. I am wondering if it is correct as I feel it is dangerous if it...
I tried hitting hammer and all but it didn't come off so i might buy https://www.harborfreight.com/three-jaw-puller-set-3-pc-63953.html
I bought this but this didn't work...
I am trying to open the fly wheel tried to use screwdriver to hold the cup and wrench to turn. This thing doesn't get loose. I even smacked with rubber mallet and put wd 40. Next thing I will have to do is buy torque wrench.
I have massimo mb 200 and I did a mod of adding filter, new carburetor, torque converter, and 0.038 main jet. I had series of issue with original carburetor so bought new twice. First one had a lot of jerk and used to turn off. Now bought different one and put the 0.038 main jet. The RPM is too...
I am not able to unscrew the crank after trying for hours. I have a socket wrench that fits the head but when i rotate the clutch plate rotates. I can stop the clutch plate front from rotating but not what is behind.
I have this wierd noise on throttle. Is anything loose or something. I am concerned for safety. Is it normal.
It turns off after a while and not start. Is it low fuel or carburetor issue or spark plug. I tried to look at carburetor and got the fuel pipe off. Now I can't put it back because it...
Questions about moding Massimo Warrior 200 Beginner
Hi guys new to this sub had been looking on it before I decided to get the mini bike.
https://www.massimomotor.com/MB-200
I have few questions on mods.
I want to mod the bike but do not want overly complicated altering like grinding, welding...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.