governor

Hey guys I'm looking for tecumseh part 30865 link. Part is not available anywhere. It's the only part I need to complete the bike. Please help if you can.

So I just picked up what I believe is a home built MB with a 65 4HP Briggs. Cleaned the carb and gas tank and it fired right up but won't run with a load on it. my thought it the throttle config is wrong I have looked and looked and have not found anything that is the same config as what I...

hello, i have a tecumseh model H35-457 66Y 3.5 hp mator and need help with getting the throttle to work right, i have all the correct spring and governor lever, but the problem is that the throttle stays wide open now, it wont go back to idle speed, what makes the governor lever go back so it...

Just picked up a somewhat new GX160 that was seized. Ended up finding a governor bushing laying inside the crankcase. Pulled that out and freed the piston now she is a great running motor. No damage! Only problem is there is no working governor now. Later on I will be investing in a ARC rod and...

OK got a friend that likes my 212 so much he put one on his Go cart, he was asking me if he could just un-hook the governor rod from the rod that comes up out of the engine, and just hook his throttle wire up to the carb eliminating the governor that way so he wouldn't have to take the engine...

Just wondering what governor spring I need (from the OldMiniBikes Warehouse site) for my 1976 Briggs 5 hp with the Pulsa-Jet carburetor. I'm "restoring" the bike and want to replace all serviceable parts to new ones. The bike also doesn't have anything as far as a throttle on it. I can post close up pics...

Omg

OK, so I'm new to the mini bike scene, and at modifying Predator engines. Been reading in here a lot about the importance of either not modifying your engine by removing your governor, or replacing the rod and flywheel if you plan to do so. Just can't find a dedicated thread of instructions...

hello all, So I was riding around and the throttle got stuck. I couldn't fix it on the spot as my hands were cold and all, so I just rode home with the choke on. It think it is a governor issue, watch the video. I'm a little confused with the linkage as I don't know if a springs loose or missing...

I'm keeping the stock Lifan 2.8 hp on my dirt bug for my young kids. Through searching the website, I've figured out the bottom two springs(smaller one not in pic), but would like to see what I'm missing in the upper linkage. Was wondering if someone could post a pic of their stock Baja. Thanks.

Ok so I recently got the 212 and put it on my mini bike. Now when I got it where the throttle hook up is suppose to go which is on the governor throttle I put it but it was super stiff. So I eliminated the governor throttle and ran my throttle cable to the little swing arm thing under the gas...

Pulled the governor out, billet rod and flywheel, new throttle linkage setup, took it for a ride and I got sad. Nothing happened. I thought I was going to to 60 MPH :shrug:

Hey guys, I just ran into a wall regarding the throttle linkage and governor. I want to use the governor linkage, but I also want to hook the throttle linkage directly to the carb (stock). I just had a new intake manifold fabricated and it brings my carb almost 2" off of the motor to clear the...

Hi guys, thanks for any input. I'm not really familiar with mini bikes. I picked up a used 2010 Baja Warrior with a 196cc engine, all stock I assume but the linkage has been changed. The throttle cable goes directly to the carb and the linkage to the governor arm is missing. Is this ok...

Ok so I took the gov out and I got it all apart but u need help filling in the holes I got quarter 20s to fill them up but I don't know if I need to thread to holes or not.

Hello, i have 6.5 predator engine and i was wondering if i just remove the governor will it give me more speed and should i replace the flywheel? Any other modification tips are welcomed!!!!!!!!!!!!!!!!!!!!!!!

Baja heat 6.5hp no governor and won't start please help Ok so I've had this baja heat for about 2-3years it's been running good and I decided to make it faster right before It started right up and then I took out the governor and put everything back on and now it won't start up it has spark and...

I currently have a HM80 that is going into a minibike project and have a few questions. In general I know that removing the governor isn't the best idea, but how do these engines fair if the governor is removed? I know I need to remove it completely from the inside of the case etc. Is...

This probably seems obvious, but there is a little twist. I have a little blue 2.5hp Greyhound left over from an engine upgrade. It was missing the throttle rod and spring (between the throttle lever and the carb), and throttle return spring. It still had the governor, gov linkage, and gov...

I replaced the carb on my stock Dirt Bug. Now the governor won't let it run under half throttle unless I manually push the governor arm toward the chain. I would appreciate suggestions for fixing this problem. L