mikuni

alum intake, new 22mm Mikuni carb, new airfilter..... The choke handle was modified to get it away from the exhaust...,,This is a nice set up for a hotter engine.. $75

Need help jetting my Mikuni VM22-133 for methanol. I'm collecting parts for GX200 clone that will need to run on methanol. I have a new Mikuni VM22-133 that I plan to use on it. (not a Mikuni clone). I'm hoping to get some, in the ballpark jetting before start up. All help will be...

I have a good used 22mm Mikuni carb for sale. Includes the intake manifold to mount to a Honda GX160/200 or Predator engine. Also, includes the air filter. I have the rubber cable inlet piece too (not pictured). I never used this carb, bought it in Ann Arbor last weekend and now here it is for...

I've been riding the bike around after completing it and it runs pretty well. I bolted the mikuni 22mm carb from affordablegokarts.com right up to the motor and it runs pretty well. i know this has been discussed in the past but i'm having trouble finding it. the bike runs better with the choke...

Here it tis...sounds awesome, but dumps fuel out of the bottom overflow AND seems to run better without the mikuni fuel pump (Gravity feed). Is this the case with a mikuni flatslide? Is there a workaround for a karting/atv application requiring a fuel pump? Thanks

The carb is a Mikuni tm24 flat slide. I have made a custom intake manifold to bolt it to my engine. The engine is a harbor freight blue clone with billet internals, ported unschrouded 14cc head with a 27 mm intake valve, and will be right around 13.4/1 CR. The cam is a NR274-0207, CM pushrods...

I have a 22 mikuni carb kit that came with just the bare cable , im I supposed to buy a sleeve to put this cable in. I been searching around and I cant find just a sleeve to put the cable in:shrug:

Ordered a 22mm from nrracing and our just came in the mail. Going to put out all together and on the bike this Saturday. Has a 130 jet and 12.5...other jet. Going to start off on the middle notch. Predator 212 No gov Billet flywheel Billet rod Black mamba cam 26lb springs Ported...

Looking for a kit like nrracing has for 212 predator figured I check before I ordered the one from nrracing thank you

I just had my motor dynoed with a 22mm mikuni and it gets up to about 4000rpm then stops. The guy says it is too rich with a 130 main and 12.5 pilot so we went down to 98 main and it does the same thing. Carb bad?? Cleaning?? I don't know what is wrong but I need to get this thing working so...

I know nothing lol there is a air and fuel mixture screw the one with the spring wrapped around it ? and there is an air screw near the back of it ? in order to get the sled to run good at idle I have to turn the air screw all the way in and back it out 1/2 turn does that sound right? thanks...

I have a 22mm mikuni carb . My ?? is when i look though the pilot jet there seems to be a cross section in it . and i can't stick a thin wire though it . Is it clogged or is there suppose to be some sort of cross section in it .

Mikuni SBN 38mm with Parsons Racing big block carb adapter. Parsons filter adapter, original pump and block off plate included to run a separate pump if you want. Couple extra jets and needle valves as well. Whole setup has 5 minutes of ride time on it. $200 bucks

I have a new real mikuni tm28 flatslide that I bought for my briggs animal engine and I have changed my mind and therefore it is now for sale. I'll include a billet flange (too big for the stock animal head) and shipping, all for $100.

Hi guys, I have a Mikuni VM28 flatslide that will be going on a Briggs animal that will be modified with a 310 dur cam and higher compression. It has the stock jets in it. Are these going to be ok or should I change them out? main=180, pilot=15, it will be on gas and later on would like to go...

Mikuni SBN 38mm on a GX390 Considering alcohol Can anyone tell me the recommended jet sizes for such an application? Are the factory jets a good start while still on gas? I believe they are 65 and 107.5 Thanks for your time

I just got my carb for my 212 predator and I hook the throttle cable up and and it only has a very short travel on the throttle now I'm using the stock doodlebug throttle assembly and cable, I think that the end of the cable that goes into the carb might be too long because I'm about 99% sure I...

As we all know we always want more hp, so I am looking to get a new carb for my predator so I need some opinions between the mikuni 22 mm or the hex 390carb also if somebody can give a small rundown on how to go about tuning the minkuni,I am trying to get some more upfront from a hp carb because...

First, Briggs to Mikuni/Kehin style carb? Tapped for pulse fitting. $10 plus shipping Next Briggs to Tilly. Has pulse fitting plugged with screw.(removable). $10 plus shipping

mikuni fuel pump $25.00 plus shipping out of CA .. money order preferred... might except paypal have to go through my buddie..... click on pics to make them bigger!!!!!!!