mikuni

I need to change direction of carburetor for fit. Has anyone used this method to redirect carburetor towards rear? Any performance issues using small section of hoe? Using radiator hose in-between cut manifold AGK - DIY Curved Manifold - Affordable Go Karts thanks

Real never used brand spanking new carb. $75 shipped

For sale is a steel intake manifold for a mikuni 22 to a Briggs 5 hp . Price 30.00 shipped

For sale is a steel intake manifold to bolt a mikuni 22 to a Briggs 5 hp . It's about 2 1/2 inches long and angles out to the pull start side slightly, to get it away from the exhaust. Price is 30.00 dollars shipped

I'm looking for a Manifold for a 22mm Mikuni carburetor. I'm located in California. Post pictures and Prices

Anyone know where i can find this intake?

Several carbs for sale... range from 18mm mikuni reportedly set up for an Animal engine to 28mm Mikunis. A couple I believe tapered bores (20-22mm) Mikunis, as well as a 24mm unit. Two 28mm off Banshee that appear to be at least partially parted out. No idea if these can be adapted for...

I have a bigblock with ported head, big valves, header, billet rod and flywheel, cam, and a 34mm mikuni. It came with a 280 main and 50 pilot which is way big and running pig rich. I was wanting to know what jet size on gas some of y'all are using with this carb so I can get close without...

wondering what the most inexpensive way to do this would be, i know OldMiniBikes has the adapter intake manifold but its over 40 dollars..... would buying a pit bike replacement carb that comes with the adapter for a 125cc motor work by cutting it in half using rad pipe or something work or are the bolt...

At the moment, I'm mostly having trouble with the throttle cable. If you've done this, what did you do? Did you use the stock cable? Did you purchase a new one? Can you use a standard screw cable clamp under the slide? Did you solder a ball on? How did you route the cable to a vertical position...

After doing some reading on Mikuni carbs, I opted to purchase a real one vs clone. Most articles talk about easy throttle cable install and lack of linkage. None discuss the governor. Someone please enlighten me. Thanks!

Sooo. I sucessfully put a honda gx200 carb on my briggs 5 hp flathead that I hopped up. I made a custom intake, welded my own stainless exhaust (about .85"ID 1"OD 2X 45 deg bends in it) It runs like a dream. Direct throttle custom made by myself bolted to a pivot point on the head. The only...

Located in Lancaster CA Asking $120 Or best offer Looks like it's in great shape PayPal preferred

I am putting a mikuni on a old style HF clone motor one of the blue engines, do I use the plastic spacer that held the spark plug wire? It looks like I need to with the NR racing kit I got, should I enlarge the intake hole to match the carb? Thanks

Title says it all, cash in hand

I am running a 26mm genuine mikuni carb with a fuel pump. I need to replace my needle valve seat and there are different sized ones. Ranging from 1.0 - 1.5 - 2.0 - 2.5. The stock size is 2.5 and it says to only use this needle valve with a gravity feed system. Anyone else thats running a fuel...

well basically the tap for the pulse line on the carb manifold leaks air and makes the engine bog out because its leaning out the mixture. I want to know what kind of sealant would be the best to make sure no air escapes from where the pulse line is taped into the carb manifold. Thank you...

Any idea what mikuni pilot jet this is? It's a #60 pilot jet in a carb I ordered and I need a #30. Its from a vm26 genuine mikuni but im not sure if its a 26-606 or a 26-8074 mikuni and if that would make a difference. Apparently at tboltusa their genuine vm26 pilot jets won't be compatible with...

Looking for some main jets size 150-200 and pilot jets 17.5-30 Will pay with paypal right away if your trusted and you can send them in an enevelope as long as they work, it don't bother me:laugh: and by chance if anyone comes across a 4J13 needle or 0-0 249 needle jet

I need to shorten the cable not the housing, if I cut it do you think I could crimp a piece of metal and solder it on. Do you all think it will work and be safe I wouldn't want it to come off and get sucked in to the motor. All help is appreciated! Thank you in advance.